Rear Reverse light/work light

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.

Lawfs

Member
Posts
43
Location
South Wales
Looking to fit a rear led light, mainly to be used to help when reversing.
Anyone have any advise on any decent ones or best position?
Seen everything from ones that mount on the rear number plate light, to cheap eBay ones to mount on the guttering...
cheers
 
Depends what you want to do.
Mount high & rotate onto tow ball or For further away work.


by number plate height will shine only straight back
Unsure what makes are good now.
 
Do you want to just upgrade the existing reverse light or wire in a separate work-light which can be used when reversing?

I have a pair of NAS style Le Perei reverse lights (one each side) and they light up even the darkest area whatever the weather, fully road legal and don't need any wiring modifications.

DSCF0166 (2).JPG
 
It’ll be mainly just for reversing, so would you say one or 2 high mounts either side fitted on the guttering is better or just one above the number plate maybe?
I’ve seen these lights/fitting below in the photos.
Also did you find it best wired straight into the reverse feed or better to have a switch built in? Cheers
 

Attachments

  • 469DD68F-4F16-4962-B718-D239E04681D8.png
    469DD68F-4F16-4962-B718-D239E04681D8.png
    248.8 KB · Views: 106
  • 272747CC-7EC4-4564-A4AF-414B80B10B65.png
    272747CC-7EC4-4564-A4AF-414B80B10B65.png
    292.8 KB · Views: 84
  • 004DFAAD-B7AE-4A24-BF20-ADB9A351E775.png
    004DFAAD-B7AE-4A24-BF20-ADB9A351E775.png
    398.5 KB · Views: 111
I mounted bog standard 12V worklights on my roof-rack - two at the back and one on each side:
DSCF5018.JPG
They're on a switch down by the fog-light switch rather than triggered off the reverse lights.

That was a while ago - everything's LED these days, so if I did it again I'd probably go for one of the lights CREE do...
Having the lights on the side is handy, as I used to have to do a reverse turn through a gate to get into my yard and it was trick to see just out of the back.
 
It’ll be mainly just for reversing, so would you say one or 2 high mounts either side fitted on the guttering is better or just one above the number plate maybe?
I’ve seen these lights/fitting below in the photos.
Also did you find it best wired straight into the reverse feed or better to have a switch built in? Cheers

Im not sure where regs say you can put a reverse light these days, if they say anything at all.

So, if mine were a hard top Id put them up high, on a switch + reverse triggered relay. Thats where mine was.

P050708_14.21.JPG


Its a soft top now so it sits lower,

WP_20190421_12_20_24_Pro (2).jpg


Either way works but I did find up high was a better reverse light as it spread the light out behind me more, low down is more of a long distance focused kind of light.
 

Attachments

  • WP_20190421_12_20_24_Pro (2).jpg
    WP_20190421_12_20_24_Pro (2).jpg
    447.6 KB · Views: 88
I’ve ordered two Cree spotlights to put up high, going to wire them into the reverse feed but with a switch on the dash. Cheers for the advice gentlemen
 
I’ve ordered two Cree spotlights to put up high, going to wire them into the reverse feed but with a switch on the dash. Cheers for the advice gentlemen
If it's possible to leave them on (driving forward) you'll need a tell tale lamp on the dash I believe.
 
fitted the bearmach LED direct Series 3 replacement unit last night

its about 5 times as bright as the bulb it replaced.
dissapointed that its the same light unit with a cheapo LED panel wedged in and some sealant papped around the lens
 
Back
Top