Freelander 1 Freelander 1 1.8 loosing power

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.

arnopretorius

Member
Posts
36
Location
South Africa
Good day Everyone
I hope everyone is doing well.

I have an FL 1 1.8 and I've recently re-done the motor. The issue I have and this started before the rebuild is that while driving the car will lose power and sounds like it is lumpy and misfiring and then all of a sudden it is okay again and then not long it happens again.

I started looking into it before the rebuild and then it was okay for some time but now it is starting again.
The engine light flashes when this happens. Any advice will be appreciated.

This is what I've done so far:

replaced coils
replaced plugs
fitted new 3.5psi fuel pump with external filter
tested injectors and all is good.

I have to add that the previous owner fitted a performance exhaust and removed the cat so the rear oxy sensor is directly on the system. could this possibly cause this type of issue?

Regards
 
What age is it? I presume a post 2001, as you have replaced coils in the plural. Which is annoying, because I was thinking that this could be a coil problem as it has an electrical flavour to it.

Could there be an intermittent fuel delivery problem? You've looked at the problem already I can see...

If you have a post cat O2 lambda sensor, then it is post 2001. If there is no cat, then you may be getting fault codes logged by the ECU - which as it is emissions related, will light the engine malfunction indicator light. I don't think it'll cause reduced power though?

Have you got a decent OBD2/ EOBD reader? They're ten-a-penny on the bay of fleas. Would be helpful to know what faults are being logged by the engine ECU.
 
It sounds like it could be a dodgy connection somewhere. Is it a big job to swap the engine harness? K series Freelanders are 10 a penny in the scrappies so it should be easy to get one.
 
Hi Nodge

Apologies...it is a 3.5 bar pump that is equal to 50psi.

@ Rob.. all the codes I get is related to "Fuel trim" errors.

What frustrates me the most is it comes and goes and when it is stuttering it smells like the system is flooding with petrol.
 
Hi Rob..

Here's the codes
P0302 Cylinder 2 misfire detected
P0303 Cylinder 3 misfire detected
P0300 multiple cylinder misfire detected
P0313 Misfire detected low fuel level

To me it seems like there is something on the fuel line / system that's not happy...

Do you maybe know where I can get a diagram for the fuel lines?
 
Can you get live data on your scanner?

the misfire reports are what you might expect. Low fuel level is curious - is the fuel filter flowing okay?
 
My scanner is basic...

I've installed an in line fuel filter underneath the car like the E36 BMW has...

This issue started before that... My next step is to remove the fuel line from the fuel rail and then test the fuel flow... I'm suspecting it mighr be a flow issue and that is also why I'm trying to get a fuel line diagram.
 
Cylinders 2 and 3 are on the same coil, so it's worth swapping that out.

I'd also check the fuel pressure. The ECU calculates fuel throughput, based on a 3.5 bar rail pressure. So that's worth checking.
 
I'm suspecting it mighr be a flow issue and that is also why I'm trying to get a fuel line diagram.

The fuel line is a single line from the tank pump to the fuel rail. There's nothing to go wrong, unless the in tank pump assembly still has its filter and pump installed.
 
I had a random misfire on my old 1.8 once, turned out to be one of the short HT leads from the coil pack to the plug. I think I realised what it was as had it running in the dark and could see it arcing to the block. Changed that and it was fine from then on. I don't remember it giving any fault codes though...
 
Hi Juzza..

I replaced both coils and leads and still the same...

@Nodge... I removed the old pump and filter and modified a new pump in the housing and then installed an in line filter.. I will also check wiring to coil on piston 3..
 
Can someone tell me what the device is on the fuel rail and can this cause issues?
 

Attachments

  • IMG_20191116_090528.jpg
    IMG_20191116_090528.jpg
    235.5 KB · Views: 242
Hi Tony

Thank you..

Question is could this cause a problem with pressure and cause the car to drive lumpy and stutery?

Its seems to get better if I Rev it up but can't drive like that...
 
Question is could this cause a problem with pressure and cause the car to drive lumpy and stutery?

I've never come across a faulty accumulator, so couldn't guess as to any symptoms if it should fail. I would think it would leak though, as the fuel is at 3.5 bar on one side of the diaphragm, and manifold pressure on the other.

What's with the red goop all round the intake manifold? Presumably it's to seal a leak. Are you 100% sure it's not leaking?
 
Back
Top