What have you done on your 90/110/130 today?

My two year-old struggles with the pressure washer so I’ll be cleaning my own 90.

Still, I used it for work and got a wave from the driver of an ex-MoD 110 travelling in the opposite direction.

Filled it full of pheasant drinkers for the poults arriving in 3 days

At least it’s dry for them...

Filled me balls with loverly grease, then lubed me shafts

Started taking the roof and van sides off this afternoon, all bolts out, wooden wedges gently tapped in round and about, silicon seal to windscreen frame cut, everything now loose.
Would have cracked on with it but had to go to a bloody picnic, Sitting around drinking wine and punch (55 % Rum) eating all sorts of rubbish. As said it's a rotton job but someon--------------- yada yada.
Anyway the doris can give me a hand in the morning to get it off and put into store. Have to get a bit of a wriggle on as we have to go out for a meal with the local hunt club lunchtime. Don't suppose I'll get much done after that, p1ssheads the lot of em.

As I am going back to work on Monday I was allowed to play in the garage today
I made my new dash.....

And this is what it will look like.....

I am quite pleased with the result

My Old Landy said:

As I am going back to work on Monday I was allowed to play in the garage today
I made my new dash.....
I am quite pleased with the result

Click to expand...

Looks tidy.
Lots of switches

J

marjon said:

Looks tidy.
Lots of switches

J

Click to expand...

Yeah, a bit of future proofing I only need five of them for the current install lol

My Old Landy said:

As I am going back to work on Monday I was allowed to play in the garage today
I made my new dash.....
View attachment 183606
And this is what it will look like.....
View attachment 183607
I am quite pleased with the result

Click to expand...

I ask you....how is that going to handle being under 5 foot of water.........honestly !!. Kids today and their bling....

Cheers

neilly said:

I ask you....how is that going to handle being under 5 foot of water.........honestly !!. Kids today and their bling....

Cheers

Click to expand...

I know still, it cost me around £20 for all the parts including the aluminium and edging so easily replaced....

My Old Landy said:

I know still, it cost me around £20 for all the parts including the aluminium and edging so easily replaced....

Click to expand...

Dang, cost me more than that for the CB I wrecked at billing last year when going through the culvert.... But then that was because the water came over the windscreen and into the cab..it was cold!!. LOL

Cheers

neilly said:

Dang, cost me more than that for the CB I wrecked at billing last year when going through the culvert.... But then that was because the water came over the windscreen and into the cab..it was cold!!. LOL

Cheers

Click to expand...

The big screen in the middle was a freebie I got from a scrap car. It's hooked into the rear camera
For someone who hates technology in cars, I seem to have added a load recently

Spent an hour wiring up the dash, all switches are operating relays so I have used 7S 0.6mm2 cable back to the fuse/relay box
I have some 1.0mm2 coming for the power in and will bus out to each switch (I don't daisy chain lol) and I have put in two earth studs for a common ground.
All of the switch indicator leds are wired to these common earths (impedance <0.1ohm) on yellow 0.5mm2.

On Saturday I removed the corroded pistons from one of my front calipers ahead of replacing them.
Note to self for the future : when using compressed air to pop the first one out, get your fingers out of the way

Justin-JP said:

On Saturday I removed the corroded pistons from one of my front calipers ahead of replacing them.
Note to self for the future : when using compressed air to pop the first one out, get your fingers out of the way

Click to expand...

Ouch.

The roof is off the "Shed" so thought I would share the joy.

Had a bit of a moment taking the rear door off, after taking off the wheel carrier I was just taking out all bolts exept the top hinge when the fecking door nearly fell off. It became obvious the top hinge had bust sometime in the past, wheel carrier was taking the load.
Anyway, I've had a replacement for this bit of capping in store for the last 5 or 6 years, bought cheap off a stall at a show. New old stock. Finally managed to free off all the bolts to get the rear tub off. Made an executive decision to run a new loom on the outside of the chassis rail so just went mad with the snips. The battery box will benefit from a bit of looking at, the chassis rails want some cutting and welding on the tops around the cross member, plus a few other small patches but no where near as bad as I had feared. Anyway, tomorrow exhaust off, dampers off, A frame off and start cleaning up ready for some real work. (I have no doubt once the cup brushes start chewing metal there will be twice the welding I thought there would be. Really isn't as bad as it looks, I made nice music with most of it with a chipping hammer. Don't think it would have been too good in a few years time though. At least the tub itself is good.

Touch of rust removal on the drivers door..

and later that afternoon...

zeaphod said:

View attachment 183909 and later that afternoon...

Click to expand...

Well done for that. My doors are actually in good nick, it's just the skins that show all the dents from years of off road work.
The rear door on the other hand really does need some work, have ordered a bottom rail section from YRM, if I get it anywhere near your standard I shall be well chuffed.

Thanks Frog Hopper. There are older patches and patches on patches, so this is the last chance for the original door. It's 34 years old, so I shouldn't complain.