Series 3 Wright’s off road soundproof matting

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
You’ll have to let us know how you get on, I did mine on me own (5’ 3”) and managed but it is heavy stuff! And remember fresh blades and a metal straight edge when cutting!
 
Ohhh I took mine out, mine has a 19j fitted so they had bodged the accelator cable together and it looked a right mess, so I replaced with a proper 2.5td accelator cable and modified the pedal, atm I’m working on electrics more so indicators and hazards ‍♀️
 

Attachments

  • F060A3BE-1A70-40DD-9E33-9FEE21BFBFAE.jpeg
    F060A3BE-1A70-40DD-9E33-9FEE21BFBFAE.jpeg
    411.7 KB · Views: 209
  • 80BCA040-D301-4FA9-A1E2-3A037D97F3BB.jpeg
    80BCA040-D301-4FA9-A1E2-3A037D97F3BB.jpeg
    341.9 KB · Views: 180
IMG_6392.JPG
IMG_6386.JPG
IMG_6364.JPG

IMG_6371.JPG

IMG_6380.JPG

IMG_6388.JPG


Fitting the seatbox mat was hardest and not for the feint hearted, i thought it would be easier taking seatbox out, recent stainless screws helped but still took best part of a day to sort it, the bulkhead panel needed longer screws for the hand throttle but the floor mat went on quick, had to measure for the OD hole , and the accelerator stop bolt marked it self out!
The steel underseat covers and their latches is hard to sort and makes the mat sit up a bit although its under the seats. I may need to trim these steel covers to fit the mats better
the centre tool box I cut the mat all the way round but the outer two seats cut 3 sides with a rear hinge,

over all quite happy and although not had it too fast the noise reduction seems ok
 
Glue flash band on the inside of the doors, they act as sound boards and reflect the noise, you will not get the full benefit of what you have done without stopping the doors drumming. I then glued carpet over the top. I put the flashband horizonallty and lipped it over the frame so it would guide the water away from going between the frame and a skin.
 
Glue flash band on the inside of the doors, they act as sound boards and reflect the noise, you will not get the full benefit of what you have done without stopping the doors drumming. I then glued carpet over the top. I put the flashband horizonallty and lipped it over the frame so it would guide the water away from going between the frame and a skin.

Good tip thanks Rob I’ll give it a go
 
View attachment 183603 View attachment 183604 View attachment 183599
View attachment 183600
View attachment 183601
View attachment 183602

Fitting the seatbox mat was hardest and not for the feint hearted, i thought it would be easier taking seatbox out, recent stainless screws helped but still took best part of a day to sort it, the bulkhead panel needed longer screws for the hand throttle but the floor mat went on quick, had to measure for the OD hole , and the accelerator stop bolt marked it self out!
The steel underseat covers and their latches is hard to sort and makes the mat sit up a bit although its under the seats. I may need to trim these steel covers to fit the mats better
the centre tool box I cut the mat all the way round but the outer two seats cut 3 sides with a rear hinge,

over all quite happy and although not had it too fast the noise reduction seems ok

Nice what do you think of it? What did you end up doing with the hand throttle?
 
definately an improvement, it does cost but if you cost it per month over 10 years and it stops you going deaf!
i drilled the holes in the may to suit the throttle i did have a bulkhead cover on it that had the throttle shape cut out and i didn't want to do that but it needed screws a bit longer than existing and the connection in the engine side was flexible so still works well
 

Attachments

  • IMG_6391.JPG
    IMG_6391.JPG
    236.4 KB · Views: 173
Soundproofing resized.JPG

This is my solution: anti-fatigue mats. Advantages are that you can cut it to shape in bits and not having to juggle huge great slabs of rubber into position. It's cheap if you shop around. Cuts easily with a craft knife and glue into place with contact adhesive. Leave the floor section unglued.
 
Yes a tank under passenger seat, theres a switch for level sensor too , normally shows driver tank , press and hold to see pass tank level , and low level light will come on for either tank , it was in Landy when I got it , didn’t really use it much until big trip recently , but pass tank has leak , I’ve got some tank sealer to go in at some point
 
Back
Top