- Posts
- 5,682
- Location
- North Manchester
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,260
- Location
- Trapped inside my head @ LZ asylum
- Posts
- 5,682
- Location
- North Manchester
Ah I see. It was only about a mile long but it took the old bill 5 hours to talk the jumper down off the bridge.
For that sort of torque setting, go where you think it is, then go a lot harder on top. I still get surprised how much effort I have to put in on our big bastard torque wrenches. Doing it by feel, I'd prefer to dead lift the breaker bar, less likely to break your teeth that way.
- Posts
- 5,682
- Location
- North Manchester
I've got a 450nm impact wrench I could use, just not sure how accurate that would be.
Close enough for government work? Probably not far off just winging it, and at least you're in the ballpark.
- Posts
- 5,682
- Location
- North Manchester
I suppose if it takes the hub nut off it should put it back.
- Posts
- 18,952
- Location
- Buckinghamshire, UK. ('95 DT)
I bet most garages just put the air on max and hammer it up.
- Posts
- 18,952
- Location
- Buckinghamshire, UK. ('95 DT)
Transfer box rear seal all done and reassembled. Everything else back on and new fluids. Started up, and a horrible noise. Think I must have stressed the water pump / viscous at some stage, probably getting the gearbox back in when I was benching the engine and gearbox trying to get it to line up. PITA.
- Posts
- 58,170
- Location
- Preston Lancs.
L322 hub nut is 420nm.
Last edited:
RangeRoller dt
Well-Sprung Member
- Posts
- 14,260
- Location
- Trapped inside my head @ LZ asylum
think P38 is about 230nm, but don’t hold me to that
Last edited:
- Posts
- 58,170
- Location
- Preston Lancs.
My belt tensioner cap was
Changed it. His car is a TD6 apparently.
- Posts
- 58,170
- Location
- Preston Lancs.
My belt tensioner cap was
May i suggest >>>>>>>> https://www.ebay.co.uk/itm/17mm-HEX...m3d47f94695:g:7T8AAOSwN8FZtn0L&frcectupt=true
RangeRoller dt
Well-Sprung Member
- Posts
- 14,260
- Location
- Trapped inside my head @ LZ asylum
You may, that looks a good one for fair price.
I still have the laser one from when you showed me how to do it properly, with coppaslip so it will come off next time. Nearly lost my job over that, only intended to change belt
I still have the laser one from when you showed me how to do it properly, with coppaslip so it will come off next time. Nearly lost my job over that, only intended to change belt
- Posts
- 18,952
- Location
- Buckinghamshire, UK. ('95 DT)
Where's the fun in that?!
- Posts
- 58,170
- Location
- Preston Lancs.
Having proper tools makes life so much easier. I have a vast amount of tooling collected over the years.
Henry_b
Think outside, no box required.
- Posts
- 15,353
- Location
- somewhere else
Yes
- Posts
- 5,682
- Location
- North Manchester
- Posts
- 58,170
- Location
- Preston Lancs.
260 metric things or 190 proper torques.
- Posts
- 58,170
- Location
- Preston Lancs.
What about an L322
So it is
Ain't got one of them either
Oh dear one too many 3s and not enough 2s. Made it right for you don't tell nursey though she will smack me hard.
