killerhaggis
Member
- Posts
- 70
- Location
- Fareham, Hampshire
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
killerhaggis
Member
- Posts
- 70
- Location
- Fareham, Hampshire
Ouch
stemac33
Well-Known Member
- Posts
- 550
- Location
- Accrington, Lancs
Yea failed chain tensioner allowing chain to jump a tooth or two
tarphenry
Well-Known Member
- Posts
- 1,522
- Location
- bury lancs
That looks almost beyond repair
stemac33
Well-Known Member
- Posts
- 550
- Location
- Accrington, Lancs
Head, piston and conrod not to bad it's the chunk missing out of the cylinder wall that might give me hassle.
tarphenry
Well-Known Member
- Posts
- 1,522
- Location
- bury lancs
Bit of filler then advertise a "Refurbished"
RangeRoller dt
Well-Sprung Member
- Posts
- 14,263
- Location
- Trapped inside my head @ LZ asylum
The BMW M51 tends not to leak, just every other LR
What happened there
Chain snapped?
- Posts
- 58,170
- Location
- Preston Lancs.
The BMW M51 tends not to leak, just every other LR
What happened there
Certainly dropped a valve in a big way. If the chain had snapped you would expect several other cylinders valve gear to be damaged.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,263
- Location
- Trapped inside my head @ LZ asylum
Found this
stemac33
Well-Known Member
- Posts
- 550
- Location
- Accrington, Lancs
Chain jumped a tooth or two piston connected with valve and bobs your aunty at a guess
stemac33
Well-Known Member
- Posts
- 550
- Location
- Accrington, Lancs
Looks a lot like mine only his was pot no5 and mine was no1
300bhp/ton
Well-Known Member
- Posts
- 4,733
- Location
- Near MK
Replacing the 20 year old centre section on my p38.
Sadly while removing the centre section it became apparent the rear section needed replacing too. The pipe work was good but one silencer less so and the flange to join to the centre section
Have to wait until next weekend to fit it, hoping it’ll turn up this week.
Sadly while removing the centre section it became apparent the rear section needed replacing too. The pipe work was good but one silencer less so and the flange to join to the centre section
Have to wait until next weekend to fit it, hoping it’ll turn up this week.
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
Orded a denso repair kit for my starter motor
Finally stripped out the last of the brake system. All pipes, hoses calipers now gone. Managed to clean up and paint the calipers and sliders. Pistons not bad with a bit of 800 Emery and metal polish. Even seven out of eight slide pins were in good nick and reusable. Just waiting for the Bay to deliver all the rest of the bits to start going back in.
Note to self: either A) don't bother painting calipers, they only get s### high when reassembling or B) paint 'em afterwards..
Note to self: either A) don't bother painting calipers, they only get s### high when reassembling or B) paint 'em afterwards..
Henry_b
Think outside, no box required.
- Posts
- 15,353
- Location
- somewhere else
- Posts
- 5,690
- Location
- North Manchester
I have a sneaky suspicion my 2006 facelift was not done by Land Rover
A couple of hours later
A couple of hours later
Wow..that's random mate..!!
RangeRoller dt
Well-Sprung Member
- Posts
- 14,263
- Location
- Trapped inside my head @ LZ asylum
Ones I found are BTR5200 - not sure they are same as yours. Also check Austin/MG ones
