Meant for the bits from brit car
oh sorry mate ,
there's some on ebay that offer free postage
but can't always tell until u get to the checkout section , lol
Other what have u done on ur disco today
- Thread starter gstuart
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
oh sorry mate ,
there's some on ebay that offer free postage
but can't always tell until u get to the checkout section , lol
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
Ant u got that bit of a job dun yet
O i forgot your READIN yu BOOK
well funny enough
today i ant doing either , lol
yeh i know back in me bleeding corner in shame
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
Thanks for the replys... it looks like I'll have to do the following then...
Thanks again
- Remove the rear wheel
- Slacken off new wishbone thing
- Use a trolley jack to jack hub up to 485 is achieved
- Then tighten bolts back up nice and tight
- Re fit wheel?
Thanks again
sent u a pm
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
Thank you. I've had a good look through it and I think I'll do as laid out in my above post ^^^ losen it all off and measure it up.
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
Going back to the IID... wouldn't mind the off road info turning on on the sat nav screen...
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
It's a great bit of kit, well worth the money.
Do you have the time clock on the speedo if not it can switch that on to.
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
Yeah I have the clock on the dash but would really like the 4x4 info too.. beer tokens up for grabs
andy85
Active Member
- Posts
- 336
- Location
- Scarborough
Today I replaced the rotten coolant pipes in the rotten weather lol
Strong winds and rain wasn't good.
All seems good again.Happy.
Strong winds and rain wasn't good.
All seems good again.Happy.
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
Just finished checking my rear suspension bushes. After replacing the drivers side rear a few weeks back I had forgotten to check the hub was the correct distance away from the top of the wheel arch and this had resulted in the bushs having a twist in them. After slackening them all off and levelling the vehicle correctly (485mm from centre of wheel hub to top of arch) the rubbers are no longer twisted and fingers crossed it will improve thier life span.
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
I could literally see the bushes intwist!
Could you prehaps point me in the direction of the best place to buy a IID tool?
Could you prehaps point me in the direction of the best place to buy a IID tool?
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
I'll PM you where I got mine, I'm sure Gaz got his from Island or Paddock
discool
Well-Known Member
- Posts
- 13,493
Nothing it far too early in the day, may take it down the pub to give it a run which is a 50mile round trip, but then could go by train.
RangerSi
Member
- Posts
- 50
- Location
- Colchester
It was last night, but close enough. Lol
Replaced the rear anti roll bar bushes. The knock was getting a bit loud. What a pain in the bum getting them back in though! Especially when you're getting a good face dusting of rust off the join in the exhaust.
In the past month I've also changed:
Discs and Pads all round
Front Prop Shaft
Front and Rear Wipers
Full Service (all filters and fluids)
Drop Links all round
Power Steering Pipes (B'Stard of a job)
New 800 CA Battery
Dash lights to sort next and whatever it needs to keep them off. Then I might be able to buy some luxury items like tyres, an HD bumper and a light bar. But I'm something else will take priority.
Replaced the rear anti roll bar bushes. The knock was getting a bit loud. What a pain in the bum getting them back in though! Especially when you're getting a good face dusting of rust off the join in the exhaust.
In the past month I've also changed:
Discs and Pads all round
Front Prop Shaft
Front and Rear Wipers
Full Service (all filters and fluids)
Drop Links all round
Power Steering Pipes (B'Stard of a job)
New 800 CA Battery
Dash lights to sort next and whatever it needs to keep them off. Then I might be able to buy some luxury items like tyres, an HD bumper and a light bar. But I'm something else will take priority.
yes went down to island and picked one up
brianconwy
Well-Known Member
- Posts
- 1,112
- Location
- conwy, north wales
Changed oil and filters. Should have been simple but the last oil change was done at a National Tyres branch - special offer. The sump plug was ridiculously tight and in the end I had to get a blow torch and breaker bar to get it off. It was mangled a bit so got a new one and washer. The old one had no washer, so perhaps the fitter had used a lot of torque to compensate rather than source a washer!
The air and fuel fiters were really simple, except it then led to a problem with air suspension compressor.
The fuel filter had no sensor on the bottom and the britpart replacement seemed to have its own sedimenter but neither old nor new had a connector. Does the Britpart fuel filter have its own sedimenter?
The air and fuel fiters were really simple, except it then led to a problem with air suspension compressor.
The fuel filter had no sensor on the bottom and the britpart replacement seemed to have its own sedimenter but neither old nor new had a connector. Does the Britpart fuel filter have its own sedimenter?
Last edited:
son treated me to some of these plastic ramps, being delivered in the week
http://www.ebay.co.uk/itm/5-8-ton-H...837736?hash=item25cf9b1768:g:4PoAAOSwTuJYorRJ
http://www.ebay.co.uk/itm/5-8-ton-H...837736?hash=item25cf9b1768:g:4PoAAOSwTuJYorRJ
