Hydraulic press build

ProcrastinatorFraser · May 6, 2016

I have a 10 ton and a 20 ton jack lying around.... I've decided to make a press, after using one at a garage (huge 50 ton beast).
I shall be passing by the old metal shop later today, and i'll hopefully get to work this afternoon.

boguing · May 6, 2016

Well, it's very kind of you to offer, I have quite a few bushes to fit, but I think the postage is going to be a problem.

ProcrastinatorFraser · May 6, 2016

boguing said:
Well, it's very kind of you to offer, I have quite a few bushes to fit, but I think the postage is going to be a problem.

No, i mean i'm posting a build fred

cfwnotloB · May 6, 2016

ProcrastinatorFraser said:
I have a 10 ton and a 20 ton jack lying around.... I've decided to make a press

will ewe be makin a firty tun press then?

Zed. · May 6, 2016

A press, any pressure will make life so much more relaxed when maintaining old vehicles, I've a bench-top 10t jobbie that definitely paid for itself over the last 15 years, I've made bigger / longer using plate steel & 24mm stud-iron as the 'frame' and 30t tangye jacks for the persuasion

.

Bodgeit & Scarper or Scrapyard Engineering rule OK

Rich.

boguing · May 6, 2016

Oh, so you're not offering to do bush fitting free for all LZ members? Blimmin yoof of today.

Bobsticle · May 6, 2016

ProcrastinatorFraser said:
I have a 10 ton and a 20 ton jack lying around.... I've decided to make a press, after using one at a garage (huge 50 ton beast).
I shall be passing by the old metal shop later today, and i'll hopefully get to work this afternoon.

Well come on then lets have a look at it, its been hours. Surely its finished by now.

ProcrastinatorFraser · May 6, 2016

Bobsticle said:
Well come on then lets have a look at it, its been hours. Surely its finished by now.

Well, i've made a start...... I'm just uploading some pics now

ProcrastinatorFraser · May 6, 2016

Tomorrow i'll be popping round a friend's house to kindly steal his arc welder for a little while... Proper beast of a machine that is... about 250amp arc welder, should easily weld this up. For the mo, it's just tacked in to place.

Bobsticle · May 6, 2016

Yea. not sure those G cramps will take 50t.

Kwakerman · May 6, 2016

Hmm could also do with a coat of paint - come on get your finger out

ProcrastinatorFraser · May 6, 2016

calm yer tits down it's not feckin finished yet

cfwnotloB · May 6, 2016

ProcrastinatorFraser said:
calm yer tits down it's not feckin finished yet

furkin excuses

biggeeeee · May 6, 2016

Whats the biggest tyres you can fit on that?

ProcrastinatorFraser · May 6, 2016

biggeeeee said:
Whats the biggest tyres you can fit on that?

58cm across

biggeeeee · May 6, 2016

Zed. · May 7, 2016

Bobsticle said:
Yea. not sure those G cramps will take 50t.

But if they are properly welded in.....

Also, as an apprentice, was taught a few phrases.....

An inch of good weld will lift a ton - the operative word being 'GOOD'

And...

"I'll Put 3 runs on it, hopefully 1 will hold"

Rich

Bobsticle · May 7, 2016

ProcrastinatorFraser said:
calm yer tits down it's not feckin finished yet

Bone idle like the rest of the frogs.

Kwakerman · May 7, 2016

Bobsticle said:
Bone idle like the rest of the frogs.

Bet he still hasn't painted it yet!

ProcrastinatorFraser · May 7, 2016

Bobsticle said:
Bone idle like the rest of the frogs.

Hey, i'll get to work when my lunch break is over!

Hydraulic press build

Active Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

De Villes Advocaat

Active Member

Active Member

De Villes Advocaat

Well-Known Member

Active Member

Well-Known Member

Retired - Living the dream

Active Member

Retired - Living the dream

Well-Known Member

De Villes Advocaat

Well-Known Member

Active Member

Similar threads