Facelift Td5

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Open bonnet. Remove the three screws from the top of the grille, pull grille forward at top and lift away. Undo flap in plastic moulding at the bottom inner end of headlight, remove screw holding lamp unit to body. Remove two torx screws on top of headlight unit, pull headlight forward until mounting pin comes out of rubber grommet in edge of wing, unplug wiring multiplug. Unscrew cover behind faulty bulb, replace, reassemble everything. 5 minute job once you've done it once. Takes longer if you have an "A" bar as that's got to come off first!
 
bargepower said:
Open bonnet. Remove the three screws from the top of the grille, pull grille forward at top and lift away. Undo flap in plastic moulding at the bottom inner end of headlight, remove screw holding lamp unit to body. Remove two torx screws on top of headlight unit, pull headlight forward until mounting pin comes out of rubber grommet in edge of wing, unplug wiring multiplug. Unscrew cover behind faulty bulb, replace, reassemble everything. 5 minute job once you've done it once. Takes longer if you have an "A" bar as that's got to come off first!
Click to expand...

Its my first time on the Loony Zone for months and i find what im looking for right away,,, bloody good show. :clap2:
 
bargepower said:
Open bonnet. Remove the three screws from the top of the grille, pull grille forward at top and lift away. Undo flap in plastic moulding at the bottom inner end of headlight, remove screw holding lamp unit to body. Remove two torx screws on top of headlight unit, pull headlight forward until mounting pin comes out of rubber grommet in edge of wing, unplug wiring multiplug. Unscrew cover behind faulty bulb, replace, reassemble everything. 5 minute job once you've done it once. Takes longer if you have an "A" bar as that's got to come off first!
Click to expand...

Can anyone tell me what size the Torx bolts are please?
Regards
 
The torx headed screws secure the light mounting and dont need to be undone. The light unit is screwed through this with 2no pozy headed screws. A third pozy screw is fixed through a bracket to the slam panel on the inner lower cirner of each light.
Its in the manual !!.
 
Hello.

I need to replace both the screws and torx bolts along the top of a facelift headlight, as they are all very corroded and need to be drilled out. Screws need drilling out and one torx bolt sheered when trying to undo.

Does anyone know the size of these bolts and screws please. Thanks
 
1997 Discovery said:
Hello.

I need to replace both the screws and torx bolts along the top of a facelift headlight, as they are all very corroded and need to be drilled out. Screws need drilling out and one torx bolt sheered when trying to undo.

Does anyone know the size of these bolts and screws please. Thanks
Click to expand...

That sounds more like mine. :)
 
You must log in or register to reply here.

Similar threads

J
TD5 Facelift - changing front fog light bulbs - nearside is boxed in by screenwash tank
Replies
4
Views
553
MJI
MJI
andyfreelandy
Freelander 1 Pre and post facelift module compatibility
Replies
8
Views
366
andyfreelandy
andyfreelandy
andyfreelandy
Freelander 1 Facelift Dashboard Removal
Replies
4
Views
398
andyfreelandy
andyfreelandy
S
The four amigos and fault 85
Replies
2
Views
244
Spuddo
S
Georgeblade
Disco 1 Post facelift front bumper
Replies
4
Views
820
DaveRRC
DaveRRC
Back
Top