ok i think its at the same angel i didnt drop it but i would have thought it would not take any gas if it was shut or the other tank would fill up cos there is 2 torpedo tanks on it but the gage inside still says empty bothe tanks was empty before i started

the tank was empty before i hit the pipe the new pipe is an 8mm (10mm with plastic) and it runs from the fill to the tank on the left side so and ideas why its not filling i did have to take the tank off to put the new pipe in coule that have somthing to do with it

Autogas Help hi all i recently got an old disco 1 V8 with LPG AUTOGAS fitted as i was working away on it i put a hole in one of the pipes :doh: it ran from the fill point to the tank i have now replaced the pipe and the connections with an 8mm pipe just a small bit smaller than...

hello again and thanks for the reply's my disco is a 94 v8 3.9 with lpg i have just finished all the other work on it like rusty rear floor and wheel arches so i was just thinking of making the front look a bit better i wasn't going to pay £300+ i was going to get some used ones instead but i...

hey all is it possible to upgrade my series 1 disco to the newer type head lights and has anyone done it before? i found this on ebay DISCOVERY SERIES 2 TD5 V8 FACELIFT HEADLIGHT SET NEW OE on eBay (end time 27-Jul-10 12:03:59 BST) and was wondering if i could make them fit thanks for looking

hi andyb66 im looking for 2 rear seatbelt mounts for a disco 1 do u have any ? thanks

could you let me no what position the flywheel should be in for a diesel 2.25 my pump has a DPA no. 3249F51 i think its hard to read in one of my books it says i should set it to the 13 mark on the flywheel the other says 15 ?? dose anyone no which it is many thanks for all your help

thanks for that i will look in the morning,

ok looks like i am just going to have to buy one

hello all i have been working really hard to try and get my series 3 landy to work properly after a fall rebuild i found out that i had the fitted the vertical cog that funs from the crankshaft was fitted 180' out witch made the engine over heat and blow that head gasket i have just...

ok i have found this web site http://mk1ultra.com/mods/w_terminal.html hear are 2 pic i took after taking the black cover off i think the wires i have mark are the ones that he talks about in the web site duse this look right to you i dont what to do it all put it in the car and find out i did...

thanks very much Dr pepper the rev counter i have goes to 8 ( x100) and it has a switch at the back for 4,6,8 cylinders i think that the first thing i should try i to fit a w terminal to the alty i have a new Lucas alty on my desk atm come this morning if you would be willing to give me...

a diesel duse not have a coil !! duse it ?? and yea its the diesel 2.25 engine i have and want to fit the tacho to

hi all i would like to fit a rev conter to my 2.25 diesel series , i have fitted one before on a nother car and i had to connecet the signel cabel to an out put on the alternater could some one ell me where i can pic the signal up from on this i hav had a very good look at the alternater and...

i have been back to my books to try and see if i have mist something it says all about fixing the engine but there is not one page that says anything about what to do now its back in the only thing that it says is to set the slow running speed on the idea screw on the fuel pump i have tried to...

np dont forget to get the air out of the fuel pump 2 because if its fall of air it wont pump what i did was when i changed the filter for the first time i didnt prim it after and just started it and she ran fine for 30sec then died as you would expect so had to do all that and it started...

i had that problem there is an air vent screw near the top of the fuel pump loosen that and prim till fuel comes out then do it up, after that loosen the one of pips to the injectors and get some one to turn it over till you see fuel coming out then do it up again and move on to the next one do...

thanks for your help

Hello All and thanks for reading i have recently rebuilt an diesel 2.25 engine for my 88" series, the engine had a rebore , crank grind , new valves the works. i have put the engine back in now and it dues run with a spray or cold start but i don't no how to set it up from now i have turned...