1. Baileyroverq

    P38A Calipers front

    See service repair 70.55.92 Land Rover workshop manual which is the same as RAVE which is what I work from no mention of depressurisation of abs before caliper removal the only thing I think I may have done too soon was press the pedal to seat pads before the bleed but then when I decided to do...
  2. Baileyroverq

    P38A Calipers front

    I do hope it's not the pump Brian it isn't making any strange noises just the accumulator coming on and off And wammers I did the bleed exactly as you state in your reply but still had soft pedal, if using a power bleeder if I buy one do you still do the 4 second on/off for the rear brakes...
  3. Baileyroverq

    P38A Calipers front

    So couldn't get the fronts to bleed and went for the full bleed i.e. master, fronts, front master, rear master, rears engine on 4 off 4 still nothing but can I assume if the accumulator is kicking in every time the pedal is pressed and it is taking over 55 seconds to fill initially that it needs...
  4. Baileyroverq

    P38A Calipers front

    Thanks for the help so far am having another go tomorrow any ideas how to get to the rear master bleed nipple as it is tucked up under the fire wall and difficult to see let alone loosen and tighten when needed
  5. Baileyroverq

    P38A Calipers front

    Hi all, I have a bit of a problem: you see I checked the front brakes on wife's 2.5 dse and found the piston dust covers were shredded so I bought new calipers and fitted them fine. The problem is the bleed of them. I had clamped the hose off before, so I assume just gravity bleed, then a...
  6. Baileyroverq

    P38A Blend motors

    That's what I thought Pete no open cheque book symbol on screen and everything works I did calibration twice now still no heat on drivers side will have to see what readings I get when putting the panel through its paces
  7. Baileyroverq

    P38A Blend motors

    Thanks for that I will look into it and let you know what I find I didn't think it was the blend motor as I had no book sign
  8. Baileyroverq

    P38A Blend motors

    hi My right side heating has stopped working I have put nanocom on and no faults show so have forced the heating to both sides and it works return control to ECU left works right doesn't has anybody got any ideas before I strip out the blend motor to change it many thanks
  9. Baileyroverq

    P38A Chip

    hi I have a 2.5 dse which when purchased had been chipped apparently but when I looked in the engine bay I found the chip but all it was connected to was itself ie the cables had been looped back round and plugged into each other Now I have no idea what make the chip is as there is no writing on...
  10. Baileyroverq

    P38A Clunking noise

    Hi all thanks for the replies sorry for not responding sooner but been out until now good thought about the damper will check it out tomorrow and yes the gate posts are still upright I think at least Jeeves hasn't said anything to the contrary also not when reversing but when turning left or...
  11. Baileyroverq

    P38A Clunking noise

    hi On my 1996 p38 4.6 I have started to notice that when I am manoevering slowly I get a single clunk from the steering it doesn't happen all the time as well initially I thought cv joint but I can't see anything obvious Hopefully you guys have an idea where to look Thanks in advance
  12. Baileyroverq

    P38A 2000 MY 2.5 dse automatic

    put nanocom on to turn airbag light off but says permanent fault, code 050 does anyone know what this is please
  13. Baileyroverq

    P38A 2.5 dse

    Hi thanks for replying Yes the central locking works fine and no the switch on the door is a no no
  14. Baileyroverq

    P38A 2.5 dse

    hi just got the new Range Rover 2.5 dse but have one niggle with it the n/s rear passenger window does not work when button is pressed nothing no motor sounds or anything is it a fuse but surely the fuse would do all and the others work fine any help please
  15. Baileyroverq

    P38A Bulbs

    Hi I did this yesterday could not see anything suspicious in there and I'm pretty sure that it went back in ok
  16. Baileyroverq

    P38A Bulbs

    Thanks for replying I'll pull them out and check just to make sure
  17. Baileyroverq

    P38A Bulbs

    Hi all Has anybody had the message centre randomly throw out bulb failure warnings only to find bulbs are ok because this keeps happening to me first the indicators then the side light o/s now the high beam any ideas where to start checking Thanks in advance
  18. Baileyroverq

    4.6 on lpg oil loss

    Have just been out checking the levels and have found that the engine oil is low but there is no leaks anywhere to be found it's not smoking or making any noise it shouldn't do where could it be going any ideas greatly appreciated:confused:
  19. Baileyroverq

    Looking for new

    Looking for another p38 for the wife this am I mad or what
  20. Baileyroverq

    Dash bulb

    Cheers I'll check them out