Yeah I set timing to TDC and engine sound nice but was underpowered. I fixed timing so crank is pointin between cams and there is now power and idle is great BUT that tapping sound came back :( I can't understand how that is possible...

Hello! My range rover don't start anymore. When i try to start it starts cranking and first it sounds like it is going to start but then it just keeps cranking even when I release key it cranks. I took off battery + cable and let it be about 10min and then connected it to battery - for 10sec...

Engine is now built and it runs quite nicely, just small tapping sound. But it seems quite underpowered and idle is rough. Maybe timing isn't correct. Top is good but in crankshaft it is now adjuated as tdc and crank pulley mark are in line? Is that correct. And i didn't use silicone.

One tappet is stuck and I also noticed that it is bit different. All others height is 26mm but that stucked one is 24mm. When I looked them from ebay all tappets are 24mm

Tes it was first start up in year but I have driven it hot and some few kilometers and I also tried rev, but didn't help. I dont know if there has been head work. Belt and water pump was changed year / 1000km ago. I took hydraulic lifter apart and I will clean all of them. If it won't help...

1.8 freelander keeps horrible tapping sound. It sounds like diesel. I just bough it and it has not been driven for year. Camshaft sensor and alternator was also bad. I replaced them. Oil looks good. I measured cylinder pressures and 1cyl has only 6bar when others have 8-10bar. I took camshaft...

Hello! I have autel maxidiag md-802 diagnostic tool and i wan't better one. I need tool what can read all land rovers and all system. I have few p38 and i can't read eas, srs or abs. And it would be great if it could do other thing than just read fault codes. Some tool like volvos vida dice...

Got it working :) fuse of ecu was burned. I checked them and all looked like okay but when i double checked one was burned so that it looked like ok

Immobilizer is programmed off the ecu and immo is by-passed in gems

I bought 1998 range rover p38 with 4.0 V8 and automatic transmission. It is usa model. It has not been running over 10 years because immobilizer was on. I bought ecu where immobiliser is removed. And i by-passed it. Engine cranks and there is pressure in fuel lines. I changed all coils and...

There is one discovery 3 for sale and it is quite cheap, but its injectors has been leaked and cranksbearings are done. There might be some damages in pistons, crankshaft and in cylinders. So it needs a new engine. New engine costs a lot and it would be cheper to buy peugeot 607 with 2.7 hdi...

Yeah i got cd changer working :) There was Navigation cd on 1st slot ;D I tried to put it to navigation cd slot in trunk but navi won't suck it, i pushed it far as i cuold with finger but nothing, and eject button don't work... And i bought 2005 bmw BM54 module but it has round pins and range...

It is almost a year so i don't really remember. But I remember something that i used those needles to connect 12v to lock. So i bypassed microswitch...

I found the cd changer, but it is broken because it won't give cd tray. But how i get usb or aux for my RR?

Hello! I just bought my dream car Range Rover Vogue TD6 2003. I want iphone / usb or aux input. And i have sirius satellite radio. It has tape slot behind front panel and satellite disc slot in trunk. But it doesn't have cd changer? or then i just couldn't find it? but behind "mode" button there...

So i bought 2004 discovery 2. It has three amigos and fault codes are: -rear left abs sensor signal too low -rear right abs sensor signal too low Earlier it also had -rear left abs sensor signal erratic Seller said that fault came when rear diff was repaired. I checked rear left sensor, cable...

Now i have replaced right rear and left front sensors and left front abs ring. After that i erased codes and light went off. But after few hundred meter in corner light turned on. Fault codes are now left front abs sensor output too low. I can erase it and light goes off but in next corner it...

This is quite rare car in finland so i will order new

Lets try, i will order new one or can i test that old?

I unplugged connector from abs box and checked ohms from pin 3 and 6(rear right sensor) and my multimeter shows 1.1300 kOhms. Is it good or bad? My fault code reader is autocom cdp maybe it isn't enough good to remove codes? When i press remove fault codes it removes them and when i deconnect my...