Sometimes looking at an issue the next day provides the answer. :D :D

Okay so I think I've sorted this - clearly not looking properly at 11pm last night when I was trying to fit it. If you look at the sixth photo, you can just about see the stud from the mount sticking down, this was resting on the chassis leg...

Along with how long before current insurance runs out and sometimes changing your job title /occupation!

I know, it’s a make your own easy decision, just ensure it doesn’t impede changing prop

Those prices

https://www.rolan.com.au/vehicle-parts-accessories/safety-security/driveshaft-safety-loops.html It is a thing apparently , do you need to buy OEM or can you ,are your own

Yes Its is standard and very good condition, he says its ready to fit but needs spigot bush.

Hi Tom You could turn your roof rack round so its open at the back then the tent will fold down flat. Then there's the option of an annex to go down the back ect here's my set up from direct 4x4

Should message eBay guy ask if it’s standard size and has any wear

Just completed a 120 mile round trip, performed excellently with a new top speed record of 60mph. it had a bit more to give and was remarkably stable but I didn’t like revving the nuts off the engine with the addition of feeling each of my inner...

Don’t worry it will ease off after the first 12 months, keep it moving 😀

Yes that’s the one, but try cleaning up yours first it might be fine

Yes was going to replace bearings anyway, Funds are low at the moment so hoping to get away with just new rings and maybe honing the bores, but still need to get the crank checked at machine shop.

I had another look, it's totally my fault. They do with or without mesh. I thought that meant the actual mesh screen. What it actually means is recessed for mesh, or not recessed for mesh. Looks like if I cut of the tabs I can custom fit it 🤔🙄

https://shielderchassis.com/products/land-rover-series-3-88-109-inch-galvanised-bulkhead Looks like the bulkheads are the same just whether the vents are supplied it not?

Well they need replacing! Just seen a nice 200tdi crank on eBay decent price

If the bores are ok and within tolerance of the +20 oversize and pistons not worn or damaged they can be used again but then youlll need to check the end gaps of piston rings in the bores to see if they are in spec if they are use again without...

Yes it’s had a rebore. Hopefully won’t need another

Found this might be useful, and you can re grind the tdi crank according to doc

Yes, 100% sure all clean & tight. Thanks

Some higher res photos would be better a few MB rather that KB ,but the area where the crank seal runs looks better, I cleaned bearing surfaces with some 1000grit wet and dry and some wd40 Need a mic to measure diameters to check, not sure you...

Ah so the clearances were to tight? I had in my mind they would be slack, if that is the case that makes a lot of sense. If that is all it was I would be buying a lottery ticket:banana:

Think I’ve had exhaust noises coming out of air filter when one exhaust valve not set properly as that was only way gas could get out! , glad you sorted it

Can confirm it was the tappets! Just did them (took 2 hours as it was my first big engine job 🤦‍♂️) Have a listen to this and compare!

I would leave pump on for now , if you rotate crank until all the timing marks line up ,then you can insert the locking tool in pump then release the tensioner wheel to remove belt , then you can unbolt pistons and push them out top of block with...

Do you know what the 'click' is ? It's likely that it is the starter solenoid. The contacts wear and don't make proper contact so there is not enough current (power) to turn the starter motor/engine over. Your battery may also be a little flat...

Posting for future reference in case ever needed! Finally found the correct grub screw size: 10/32 x 1/4

I've reluctantly started to give Leylandi series 3, some protection today. Last weekend I used a wire brush on a drill and white spirit to remove old waxoyl then jetwashed. I used Jenolite rust converter and 2 coats of Buzzweld chassis in one...

It Passed, only 1 advisory , it has an oil leak.......dont they all