I remember you making them. Maybe they are just falling off in sympathy with yer FL doors :D

Yes indeed, it left no trace. The oil is still clear from the last change so no black trail. I did put a tell-tale there and it came away clean and dry (still is) but after tightening the cover T-bolt a bit more the seep/leak has clearly stopped.

Glad you sorted it!

Steel tres étrange zat you did not spot it running dahn zee sahd uv zee engine top!! 🤣 🤣

Stirrer! ;)

Euh, 'allo 'Allo!!!

Henri🤣🤣

OK it is time to "fess-up". It was the rocker gasket after all. :) The LH screw-down T-Bolt was not as tight as the RH side one. One extra quarter turn (to match the resistance felt on the RH side one) and the leak stopped. So well done all...

I remember quite a while back reading about a uber-tough phone in a LR magazine they tested it to real extremes and it put up with it. Things like strapping it to a Defender wheel and going off road wiv it, floods, the lot. Made by JCB or...

Look for a griffin case. Makes the phone a bit bulky but saves damage

Loads avaiable. J

Gorra link? Change the www to ww***w at the beginning to stop LZ messin wivvit.

quick check says something like this 🤔 J Edit: that dont show:vb-confused2:

Me doors are straight. Still atta right angle. Eye put pic's on ere some years ago. Each one is a square version ov a number 8, wiv two diagonals, both wiv notches top and bottom so the diagonal cant move. So they is quite strong. Me hinges dun't...

Been out for a quick blatt around town in the mini. :) It always makes me smile. Oil leak sorted it seems. :) Worried a bit about over-fuelling and bore-washing the engine, but hard to say without an AFR gauge fitted. Nearly time for afternoon...

Ma hippo needs to get his dpf to 23 so he can regenerate. Few weeks ago he were on 17. Checked last nite after wuk and he were on 22.5. He dun't do many miles so it wood take several days to get to 23. We both like to go ferra drive to hexercise...

Check the edge of the door is vertical with a spirit level, in the closed position and again at 90 degrees open position. This will indicate if the hinges need adjusting.

... which is why it isn't clever to swop the lifters around!! Camshafts are fascinating things. I had a member of my club who designed his own cam and had it ground to his spec by Kent or Someone. It ran fine. I put a high torque cam in a Pinto...

The main reason for the running in is to mate to the lifters

Different makes charge more as their kit is betterer. Price matching to a price point or competitor sometimes. Either was its betterer for the environment if peeps use one charger and set of batteries across multiple tools.

Fell out wiv me garage doors recently. They have moved so the wheels dun't touch the ground when closed. This means they pull apart slightly so the key has started to bent as turning it requires the doirs to pull togeffer. Eye has put some bits...

Don't think she's much into the latest fashion. Mayeb he's got her some more copper!!! 🤣🤣🤣

I dont know thats quite a few outfits for the price of the scrap value ;). J

You'll have noticed we are not at "Rock and Cars". W has to keep her foot up and off it, and I am not trying to wheel her around a town crowded with peeps. I had the devils own job getting her from the parked car to the chemist's yessdi. No...

Nitriding or summat maybe, but they would all need to be treated or they would all wear out in nothing flat. usually heat treament, induction heating for instance. And as mentioned above they have to be run in properly with the special lubricant.

This tells us a bit more about V8 cams, bit off topic though. https://www.v8forum.co.uk/forum/viewtopic.php?t=9405

3.5 engines were renowned for getting through cam shafts. No idea why though.

Well I think we have given him some good ideas of where to go with it.

Untill the OP comes back and answers some questions. We are just guessing. If a new cam was needed then he could probably get it redone there, they have great engineering capabilities there. J

For thos who watch "Repair Shop"...