Now then, having trouble setting navigation on Freelander 2 I can put the address in and then get to screen with all the arrows on it but thats it, manual doesn't say what to do after putting address in to get it to work Old person so please be...

Lets see the oil you drained out. What did you put back in? What gearbox do you have? ATF is red, so maybe some water has got in. J

Is that a yes or a no ?

I just bought a 2008 Td4 and can't answer any of your questions, only know the navigation thingy is complicated until you read the instructions :D

Morning All. :D Ruddy cheek! The Paper's gone up by another 10p. :( Bright but cold here. Have a lovely day. :D

Again thanks 🙂

Officers pips. https://www.google.com/url?q=https://www.greatwarforum.org/topic/49957-what-is-this-badge/&sa=U&ved=2ahUKEwjI3ZSvxbKMAxXXUkEAHZnMNX4QFnoECAIQAg&usg=AOvVaw1YRlOzP4JFYfyuY6Pi0F7q

Google lens sessits this https://www.ebay.co.uk/itm/326188755306

Thank you 🙂

Found some badges, large button size Anyone identify please

Link pipes on return from injectors ?

There were some very nice cars at the Canvey Island Classic Car meet today. Here's one.

Afternoon (already) 🤔 Having a day off and chillin Have a good Sunday all :)

We had strong winds last night, plant pots & garden stuff all over the place, part of the neebs fence down too. Suns out looks to be much brighter next week. Im off to have a look at the security light. Then I will need to go shopping or I'll...

Morning All. :D Up early cos theres a local classic car show and I ant to take the Mini and have gander. :) See you all later, have a great day. :D

Just had a quick look at some youtoobs about calibrating torque wrenches. The methods, hanging weights off and doing maths, is very obvious and not a problem. My problem is finding the mech to do any adjustment, especially as the high power one...

Just a thought regarding vac advance Putting your foot down retards the ignition, lifting it off advances ignition to allow for leaner mixture.

Bottom, , top is attached to damper piston , bottom is at jet end You can fine tune by rubbing brasso on to remove little at a time

File a little off the bottom third of the needle, that'll give it more fuel at full throttle :)

A little blast was enjoyed. :D It still doesn't feel right. I have put in a request for a chat to the local tuning man. :) I am sure the DWP can afford it next month. :)

For boats we make a frame/mount out of angle bar (usually stainless) then sit a plastic marine battery box in the frame & bolt it on then use a webbing strap to stop the battery moving. :) Truck may need tie bar across to secure it.(instead of a...

Been looking for a carrier so as I can have battery bolted to the chassis, looks like I'll have to make one Battery is 7" x 14" Can only find small expensive ones :(

Morning All. :D A Sunny start to the day at least. A bit cold though. :) No real plans for today, might take the Mini out for a blast. :) Have a great day. :D

Bus stop 20 yds from my gate, free on bus and goes straight into middle of town 😛 :D

Freelander broken already?? 🤣

Mornin Dull start today Gutter clearing today for a neighbour Off to town on the bus later Out for a pint tonight Have a good Saturday Stay safe all :)

I'm still 'ere - just about! Health problem.

He said flippers 🙂

Thanks! All you lovely folks are so encouraging and helpful. I last "spannered" over 50 years ago and only simple stuff like valve regrinding/lapping, no engine or gearbox rebuilds. Just trying to keep junkers on the road as a 18..20YO with...

Glad you got it done The bolt holes usually go all the way through, they get crusty at the bottom due to rusty water and block up below the bolt. Yours may not be drilled and tapped all the way though, not sure if all were the same