Put the buzzer on the indicator relay. It’s a lot easier.

I thought it was just an interference fit. Clean and stuff into the groove. You could go crazy with tiger seal if you wanted to, but the next person to change the seals will hate you

THAT rare?!? Blimey.

International rescue Shirley?

Try these places(Wiltshire) Contact these to see if they have space Ellisons are also a coach company & a village garage. Good work & family run. Used to MOT landrover when I lived local. http://ellisonsgarage.co.uk/ This is an independent...

Yep you will need a new cover. Remove pump off the rear of the transfer box & there may be a gear you need to remove as well. You may need a diffent out put gear depending on the above.

This was it! I could not see it except in the photo. I just got all my weight on the right hand shoe and pulled down and it clicked into place!!

Just for the record, I think I figured out what the interior lighting contact is used for, it is (cpupd be) the constant plus. In case of 13 pin sockets, 7 pin sockets don't have one. Either way, I might just use it as a constant plus, saves me...

Got the 90 back from the MoT. It passed but has a couple of advisories. A rear shock is misting slightly, a rear wheel bearing has slight play, the fuel lift pump is showing signs of weeping and the bulkhead outriggers will need welding. It’s got...

As far as I'm led to believe it's positive pressure so this shouldn't be the case. Only other things I could think of relating to this were that the wastegate is seized from being parked up and not opening fully, or the pipe I fitted is...

Blocked fuel pipe/pick up? Could also run but would not pull top gears. Fitted an override pump(was on racer) & this would pull more fuel than the standard lift pump. Piece of wood in pipe had gone up it,fitted a series gauze on the pipe after

Is the waste gate pipe been restricted by the vacuum pressure(collapsing pipe)& not allowing full movement of the waste gate?

If that is what yours is like then you should be able to lock the arm centred using that. below are some pics of the drop arm an box that I have out of the vehicle to illustrate how it work, from the pics it looks to be threaded so could use a bolt:

There used to be a classic metal grill with spot lights in it.(better than spots on bumper. High beam was operated by floor button like series motors

Just put seven pin socket on and use a 13 to 7 pin adaptor when towing 13 pin

Sad news indeed Jai. When somebody passes it always makes you wonder about the nature of mortality. Ryder was a good man and I am pleased to say I knew him. Whatever happens, I think it is true to say this thread keeps the memories alive. It's...

can you adjust the rod/flat metal on the internal pull handle to make it work?

It was me, my Ninety has series metal caps. Whack on with rubber mallet with smear of sealer on the edge.

It is .... it's held on with 5 wee studs and 10mm nylocs. FTC1379 I always wondered what the wee holes were for of the brake disk ... No good for me on my 1994 300tdi, I think the axle is a replacement (Disco ?) by the PO/renovator. Anyone need...

1949 S1 knock on metal type Early disco Both are knock on,not measured or removed to check further. They look the same size(my theory is wheel stubs are all the same design/size for most years) unless you got HD with bigger shafts

Don't know exactly but I know a hammer is involved. it's a 1989 Ninety.

Is that an ABS ring? Rest looks standard

I will be ignoring for a few days but someone will remind me to update..

Never tried… they may fit early shafts How do the series ones hold on? At least the plastic ones grip a lip

When my old Honda 125 caught fire as I was riding along [ things got rather hot down below] I was glad to do a quick bail out.:eek::eek::oops:

Ah, well. I'm of an age where we didn't wear seatbelts. I'm also into classic cars where if your pride and joy is over a certain age, it need not have seat belts fitted. So I'm still riding around (perfectly legally) with no seat belt. Think...

I’ll post a picture of my C post tomorrow, or should I say where my C post should’ve been.

Just checking in, with another coffee. Plenty of ignoring going on today. Off to tidy my garage in a minute, so will ignore from there too. @MGT

I was going to go for half a Wispa but in light of your startling claim may need to have further discussion with my LZLawyer4U. I just hope @MGT is ready for this and isn't just ignoring it. ;) 😁

@MGT have you seem the trouble you have caused… Having to ignore this thread is causing sleepless nights. Off to the doctors to see off they can help.