R4FF · Sep 6, 2012

Alliteration aside, i managed to pick up a really cheap (£10) but massively worn out "bull bar" today when i went to pick up some cheap (£150 for 5) 16" alloys.
This bull bar is rather rusty under it's wierd plasticised coating, and missing a bolt/spacer and the two lower brackets.
My questions are;
1: how do i go about stripping this horrendous coating so i can see the extent of the rust and hopefully weld/fix it... And...
2: where can i get spare fittings from, or would it be simpler to DIY my own.

Oh yeah, and i ordered a 2 inch lift kit, but it only came with the spacers, do i need camber pins? There's faaaaar to many arguements for and against for my liking :cool2:

blue beasty · Sep 6, 2012

Heat gun to soften and peel off

teddywood1 · Sep 7, 2012

i would not put a lift kit on unless you like changing cv joints as there are at a angle and do not like being that way. you bull bar I gather it is plastic coated the usuall way is to burn it of and you can get them recoated

Diesel Do · Sep 7, 2012

teddywood1 said:
i would not put a lift kit on unless you like changing cv joints as there are at a angle and do not like being that way. you bull bar I gather it is plastic coated the usuall way is to burn it of and you can get them recoated

I've put a 2" lift on mine, my cv's were fine got three months then got a knock from the NSR outer one! Pulled back the boot and regreased it, it's been fine since!
Ref camber pins, I didn't fit them originally, I daren't go over 50 in the wet, it was scary! Camber pins fixed it

Freelaner · Sep 7, 2012

some have probs with lift kits some don't.....some use camber pins and some don't.
some have to cut the body to allow clearance, some don't

try it and see would be my advice

strange_days · Sep 7, 2012

Freelaner said:
try it and see would be my advice

Sometimes words just aren't required

Freelaner · Sep 7, 2012

strange_days said:
Sometimes words just aren't required

don't knock it til you've tried it.........hold on.....you're a civil servant, you have

ound:

strange_days · Sep 7, 2012

Freelaner said:
don't knock it til you've tried it.........hold on.....you're a civil servant, you have ound:

teddywood1 · Sep 7, 2012

Freelaner what is that woman doing and what has she in her hands

Diesel Do · Sep 8, 2012

teddywood1 said:
Freelaner what is that woman doing and what has she in her hands

What woman???

Diesel Do · Sep 8, 2012

Freelaner said:
some have probs with lift kits some don't.....some use camber pins and some don't.
some have to cut the body to allow clearance, some don't

try it and see would be my advice

Some can't drive well enough to realise how bad they are! If you do a two inch lift "adjusting" the inner wings isn't an option! One inch I think you'd be ok

Hippo · Sep 8, 2012

Diesel Do said:
What woman???

Yer not logged in or yer not got "enable signatures" ticked in the "edit options" part of yer profile.

R4FF · Sep 8, 2012

cheers for the replies, i'm gonna get the VMs back at camp to have a look at fitting the kit for me... if it needs the pins, i'll buy the pins... if it needs the wing cutting i'll cut it... if it doesn't work, i'll go for the 1" lift

fitted my new 16"ers last night on 225/75R16 bridgestone dueler ATs, had to use a 6mm spacer as they're the older alloys... seems to have made road driving alot smoother and sorted out the difference with my satnav vs speedo. just need to see what they're like off the road now :cool2:
i'm hopefully gonna get the metalsmith at work to show me how to patch up the bull bars, so will try the heatgun idea on the plastic sometime early next week and keep you all informed on how it goes

R4FF

Member

blue beasty

Leaks an prone to bits dropping off

teddywood1

Well-Known Member

Diesel Do

Well-Known Member

Freelaner

Landy Driver

strange_days

New Member

Freelaner

Landy Driver

strange_days

New Member

teddywood1

Well-Known Member

Diesel Do

Well-Known Member

Diesel Do

Well-Known Member

Hippo

Lord Hippo

R4FF

Member

Similar threads