Who would you recommend for a new 88 galvanized Chassis

Matt DeVeants · Mar 20, 2010

Dear All,

I went to the MOT station yesterday (19-03-2010) to see if my new SIII would pass.

I new the chassis needed work but after lifting it was obvious that it needed a lot of work and as I was going to change the chassis for a galvanized one before taking my SIII to the tropics (when I have finished
my Masters) I think that it would be cheaper and easier to do the job now than the repair job and chassis change later.

So the question is:

Who would you recommend as a good/best/favorite place to buy an 88 galvanized chassis?

and

What advice would you give as to treating it before fitting? (i.e. painting etc.)

Yours,

Matt

fanatic · Mar 20, 2010

Richards Chassis Land Rover chassis manufacturer, LandRover

gcoo8154 · Mar 20, 2010

people only paint them to make them look like the original theres no need too

109party · Mar 21, 2010

people paint them so it doesnt say i have a brand new galvi chassis im worth alot to be stolen and broken up

Blippie · Mar 23, 2010

Another vote for Richards...

Cheers

Blippie

protactor · Mar 23, 2010

Mine is Marslands. I think there is little to choose between the two. I etch primed and then gave 4 coats of Tetra Schutz. It don't look galvy anymore to the scrotes.

jessejazza · Mar 26, 2010

Matt DeVeants said:
a] Who would you recommend as a good/best/favorite place to buy an 88 galvanized chassis?

b] What advice would you give as to treating it before fitting? (i.e. painting etc.)

a] Richards are the best i'm always told

b] You need to use what is called a Mordant solution. It is mostly phosphoric acid. Well worth using on all prepared steel whether followed by etch primer or plain primer. Mordant is a clear liquid which when brushed on plain steel will turn it slightly blackish with whisps of whiteish... which indicates that it has been applied on an absolutely clean surface.

Most manufacturers produce it... here's an example
- Witham Oil and Paint

storm99 · Mar 26, 2010

Im on the Marsland side..great customer service.

Matt DeVeants · May 17, 2010

Hi all,

Just to let you know I went with Marsland in the end.

Thanks to all those who contributed.

Matt.

Sean · May 17, 2010

jessejazza said:
You need to use what is called a Mordant solution. It is mostly phosphoric acid. Well worth using on all prepared steel whether followed by etch primer or plain primer. Mordant is a clear liquid which when brushed on plain steel will turn it slightly blackish with whisps of whiteish... which indicates that it has been applied on an absolutely clean surface.
[/url]

also known as T Wash

spartan · Jun 3, 2010

storm99 said:
Im on the Marsland side..great customer service.

i beg to differ with that, i bought a series chassis from marsland, and to be honest it was fine, a couple of years later i purchased a defender chassis of them, i had put all the landy together, came to fit the doors, not a chance, hitting the tub one side, other side not even hitting the frame, miles out, tried everything, i took all the bodywork off, measured the chassis from corner to corner and it was 5/8 inch out of square

, contacted marsland who said this was not possible, they sent a engineer out, after appox 2 hours of messing about he admited the chassis was twisted,

they offered to swap the chassis when i had stripped everything down, and came with a td5 chassis with 200tdi mounts on, after checking it was square, i questioned would all my bolt on bits fit they said yes, how wrong they where, none of them fitted, i spent approx £400 on new td5 bits,

after a letter to them explaining all the problems i had, they never had the decency to even reply, no compensation, nothing, look at the money i would have lost if i had to pay a garage to do the work??. needless to say im not reccomending marsland

ed.poore · Jun 3, 2010

Bit late but I got mine from Richards and had fantastic service from them.

MakAtak67 · Oct 12, 2018

1972 Series 3 21/4 D.

Full ground up rebuild.

Galvanized Chassis painted to hide the new gleaming bits.

Delighted with result. Cheque book devastated.

Phil Gibbs · Oct 15, 2018

ed.poore said:
Bit late but I got mine from Richards and had fantastic service from them.

Same here, I went Direct to Richards , they even stamped my chassis number for me,

Who would you recommend for a new 88 galvanized Chassis

Matt DeVeants

New Member

fanatic

RESPECT IS EARNED, BEATINGS ARE FREE ;-)

gcoo8154

Well-Known Member

109party

Well-Known Member

Blippie

Well-Known Member

protactor

New Member

jessejazza

New Member

storm99

Spreading Joy & Harmony

Matt DeVeants

New Member

Sean

Banned

spartan

Member

ed.poore

Active Member

MakAtak67

New Member

Attachments

Phil Gibbs

Active Member

Similar threads