phatwake360
Active Member
- Posts
- 104
im after the piece of the snorkel that goes on the inside of the wing and eventually connects up to the airbox (passenger side)
snorkel part needed
- Thread starter phatwake360
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Litch
Well-Known Member
- Posts
- 2,235
- Location
- Oxfordshire
What make of snorkle or do you mean you require the standard air-intake ducting?
Vehicle & engine info might be of some help as well.
Vehicle & engine info might be of some help as well.
wiltshire landyman
I’m back
- Posts
- 15,062
- Location
- salisbury plain wiltshire
hold on i will get my crystal ball
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
i told you to go to the docs about that
phatwake360
Active Member
- Posts
- 104
ok smart asses my descriptions not to clear 
its a 86 def 90 which was a 2.5 petrol now a 200tdi ive got a safari type snorkel which is for the passenger wing unfortunatly i dont have a vent on the side of the wing so ill have to cut a hole in the wing but i need the bit that goes on the inside of the wing and the round airbox pipeing fits onto (see clear as mud)
its a 86 def 90 which was a 2.5 petrol now a 200tdi ive got a safari type snorkel which is for the passenger wing unfortunatly i dont have a vent on the side of the wing so ill have to cut a hole in the wing but i need the bit that goes on the inside of the wing and the round airbox pipeing fits onto (see clear as mud)
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
ah i see..... nope not got one..... try ebay
phatwake360
Active Member
- Posts
- 104
any idea what its called??????/
Griffdowg
New Member
- Posts
- 7,194
- Location
- Somewhere in Bristol
air intake wing moulding?
if you dont have the original fitment you may be better off getting a southdown snorkel that slots down the top of the wing. the hose runs from the bottom of the snork direct to the airbox. by chopping your wing I dont think your going to get a very good seal and it may compromise your snorkel
G
if you dont have the original fitment you may be better off getting a southdown snorkel that slots down the top of the wing. the hose runs from the bottom of the snork direct to the airbox. by chopping your wing I dont think your going to get a very good seal and it may compromise your snorkel
G
khaos
New Member
- Posts
- 2,907
- Location
- Sheffield, South Yorkshire.
You're better off getting a snorkel you can attach a pipe to.
Litch
Well-Known Member
- Posts
- 2,235
- Location
- Oxfordshire
You need Duct Air (MWC1826), Duct Air (MWC1827), Dump Valve(MUC2417) and the associated fixings. Unfortunately the ducts are showing as discontinued so you will have to source them secondhand.
I agree with the above though, get a snorkle that has a spigot that the ductwork connects onto, the 300TDi/TD5 version of the Safari Snorkle is like this and gives a perfect seal but anything that relies on a seal against the bodywork iteslf is not going to be 100% reliable (what happens if you dent the panelwork?).
I agree with the above though, get a snorkle that has a spigot that the ductwork connects onto, the 300TDi/TD5 version of the Safari Snorkle is like this and gives a perfect seal but anything that relies on a seal against the bodywork iteslf is not going to be 100% reliable (what happens if you dent the panelwork?).
