Series 2 RH rear flasher not flashing

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Hexonxonx

Hexonxonx

Member
Posts
33
Location
Guelph, Canada
Good day,

Working to get my new-to-me 1970 Series IIa military ambulance safetied, and am having difficulties troubleshooting a non-flashing RH rear flasher. This is a negative earth vehicle.

What I've checked:

- The other 3 flashers work
- All bulbs work and are the exact same bulb, and I've swapped all 4 flasher bulbs in all sockets to confirm
- All sockets work, and I've replaced the RH rear socket
- 2-wire flasher module is new and works
- Checked the ground connection at rear chassis, and these are fine. There is continuity between the socket and ground connection
- Though the PO has replaced some wires at the bulkhead, they look correct in comparison with wiring diagrams

The problem socket is getting power - I can "see" it flashing on multimeter, and the voltage is the same across all sockets. But when I put a bulb in the socket, it does not light up. The only thing I can think of is that the bulb is drawing down current in some odd way that is preventing it from turning on, but not affecting the RH front flasher.

Any ideas?
 
Long shot but do you have tow bar electrics fitted ?
I had similar issue with my Series 2. I thought I traced it to a poor bullet connection in the loom, just before it entered the chassis next to the gearbox. I reworked that connection and it worked for a while.
When it went again I disconnected all the wiring to the rear lights and refitted, minus tow bar which was not used.
Lo-and-behold, all indicators working as they should.
 
Shedload said:
Long shot but do you have tow bar electrics fitted ?
I had similar issue with my Series 2. I thought I traced it to a poor bullet connection in the loom, just before it entered the chassis next to the gearbox. I reworked that connection and it worked for a while.
When it went again I disconnected all the wiring to the rear lights and refitted, minus tow bar which was not used.
Lo-and-behold, all indicators working as they should.
Click to expand...

Thanks - no tow/trailer connections, though being a military vehicle it has a convoy light on a separate circuit.
 
Hexonxonx said:
Oh, how I wish it were that easy...
Click to expand...
Usually works for me. You can never know what the bulb to fitting connections are doing with a multimeter. Specially if it’s one of those crappy plastic aftermarket fittings. Might have the power at the terminals but it sounds like it’s not taking the leap of faith into the lamp.
 
The problem is that voltmeters do not load the circuit like a bulb does. So, seeing your multimeter "flash" isn't the same, and isn't necessarily telling you anything.

The better approach is to look for voltage drops while the circuit is working. For example, put the positive probe of yourmultimeter on the metal body of the bulb, and the negative to a good earth on the chassis - if the bulb is well grounded, you will only see a very small voltage drop (0.2V or so), if the earth to the bulb is poor, you'll see a much larger voltage drop.

There are two big advantages to this approach - you don't break any connections to make the measurement,and youmeasure the circuit under load, i.e.,much closer to "real life".
 
Tall Ratbag said:
...The better approach is to look for voltage drops while the circuit is working. For example, put the positive probe of yourmultimeter on the metal body of the bulb, and the negative to a good earth on the chassis - if the bulb is well grounded, you will only see a very small voltage drop (0.2V or so), if the earth to the bulb is poor, you'll see a much larger voltage drop.
Click to expand...

Thanks - did as you suggested and the voltage is reading low (11.9v vs 13.4-14.2 on LH flasher). The tail lights, convoy light and license plate light all use a common ground connection on the rear frame and they all work fine, though I cleaned it for good measure.

Tomorrow I'll put my multimeter on the connections at the turn signal switch and the wiring connections at the bulkhead and see if I get the same readings.
 
>>(11.9v vs 13.4-14.2 on LH flasher)

This sounds like you didn't actually follow what I was saying. Look for voltage drops from a fully assembled circuit.

I'll give you another example

Imagine that you are checking the starter circuit, and you want to check the voltage drop between the battery and the chassis. You would not disconnect anything at all, but,would put your positive voltmeter probe to the negative battery terminal (assumine -ve earth), and the negative probe to a bright clean area of metal on the chassis. You would try the starter, and read the voltage drop at the same time. A high reading (anywhere above, say, 0.5 volts) indicates a bad earth connection. A perfect connection would have no voltage drop at all, and the voltmeter would read zero.
 
You must log in or register to reply here.

Similar threads

A
Rapid flashing indicators
Replies
5
Views
594
tottot
tottot
H
Indicators not behaving - any ideas?
Replies
6
Views
966
henrythelandy01
H
SteveG4TRA
Discovery Flashers
Replies
4
Views
714
SteveG4TRA
SteveG4TRA
R
LED side lights not working
Replies
9
Views
825
RickyFreelander
R
M
1985 90 Rear wiring
Replies
2
Views
1K
MelancholyDonkey
M
Back
Top