priming fuel

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
G

ghostrider

Member
Posts
30
Hi guys so all goes well filter moisture leaked off then changed filter now looking to prime it again, my question fella where the heck is the priming lever I can't locate it at all it's a 90 with a disco engine will add a pic if anyone can count me in the right direction it would help, Haynes manual only describes it not show it
 

Attachments

  • IMG_20200503_1542065.jpg
    IMG_20200503_1542065.jpg
    373 KB · Views: 265
Nice clear video cheers
Still won't prime though it's a bugger
Pumping lever up and down loads no luck
Filled filter before fitting, am I missing something
 
It's probably not on the cam or broke.
My 200 will start and self bleeds after a filter change, just let it idle until the tickover smooths out then it's good to go. The fip has its own internal lift pump.
 
The tdi does need the lift pump to run properly, you will not get full power if it is not. As others have said it may be on the cam an so will not pump. you only have to turn the engine over a bit to get it off the cam then it should work and get fuel to an open connection on the filter housing.
 
hi guys
so whats going wrong on my 300tdi
managed to operate the lift pump, bled filter off.
closed bleed screw then turned ignition on and pumped some more
felt the resistance then done afew extra pumps of the lever as per haynes
and still wont start , any ideas
i was thinking on haynes it says about injector lines with air disconnect and turn over engine till fuel comes out
is this right as i cranked it for 30 seconds+ and no fuel came through.
man i had better luck when i had an old v8 petrol
 
Sounds like you still have air in the system.

Crack the filter bleed and see if fuel comes out when you turn the key and crank the engine. If it does, close the bleed on the filter. Now crack the pipes at the injectors, See if fuel comes out there when you crank the engine? if not then carry on crank it for 10 to 15 secs, give it a rest, crank it for 10 to 15 secs etc etc.

Cheers
 
so filter bled all okay so went to injector pipes done the crank 10-15 secs over and over with no luck
battery now flat so stuck it on charge overnight so see if it takes one.
on anther thought the lift pump you guys say is notorious on breaking is this still possiple
it is even though its got resistance on it and bled fuel out the filter.
i just dont want to go down the road of changing things not broken for a simple filter change
 
ghostrider said:
so filter bled all okay so went to injector pipes done the crank 10-15 secs over and over with no luck
battery now flat so stuck it on charge overnight so see if it takes one.
on anther thought the lift pump you guys say is notorious on breaking is this still possiple
it is even though its got resistance on it and bled fuel out the filter.
i just dont want to go down the road of changing things not broken for a simple filter change
Click to expand...

Stupid question time, have you checke the 12V connection on the solenoid? you have not knocked it by mistake have you?

Cheers
 
You must log in or register to reply here.

Similar threads

J
Range Rover sport SDV6 NOT STARTING!
Replies
3
Views
1K
AllanWorms
AllanWorms
Aflyingduckling
Series 3 Fuel Pipe Issue (part 564902)
Replies
1
Views
629
steve2286w
steve2286w
DefendingLancashire
300TDI Four-parter: brake wear, lift pump / fuel filter, turbo, and bushes / squeaking
Replies
13
Views
616
miktdish
miktdish
tweedandbriar
Low Rev Throttle Response, at a loss now!
10 11 12
Replies
235
Views
12K
Tim4x4
Tim4x4
A
I'm a bad parent ( indicator issue )
Replies
4
Views
432
Hicap phill
H
Back
Top