p38 no drive

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
P

pugsley

New Member
Posts
18
hi just fitted a replacement engine into a p38 4.0 that had to be replaced due to a thrown con rod and smashed cam n piston,dont know how or what exactly happened/history of how damage occured ie speed at time ect? as purchased car from a guy who bought the car like it salvage and he never new alot of info about the engine prob said lost interest!, anyway checked location of torque convertor in box prior to fitting engine all seemed ok locating ok ,all bolted to flexiplate ok,engine runs and sounds lovely no warning lights on dash ect,checked and topped up auto box with dexron 2 oil and run through gears but absolutley no drive whatsoever,and it makes a funny noise when shifted forward at idle into park .everything is connected properly as have double checked,is it possible output shaft sheared inside box due to engine failure or could be something else less major?.would be thankfull for advice please:mad:
 
Last edited:
That horrible noise when you put it in park is normally when the box input shaft is turning but there is no oil pressure to operate the brake bands.

I can’t see it being the selector adjustment. Do you think there is any chance you could have broke the oil pump flanges off with the engine. Did it feel ok when the engine was going on?
 
I reckon the transfer box is in neutral,anyone looked to see if there is any transfer box motor issues ?
 
eightinavee said:
I reckon the transfer box is in neutral,anyone looked to see if there is any transfer box motor issues ?
Click to expand...
how do youcheck the trans box motor,would this break in the event of sudden engine lock up or would the outputshaft or torque converter not fail first?
 
Mtechuk said:
That horrible noise when you put it in park is normally when the box input shaft is turning but there is no oil pressure to operate the brake bands.

I can’t see it being the selector adjustment. Do you think there is any chance you could have broke the oil pump flanges off with the engine. Did it feel ok when the engine was going on?
Click to expand...
hi the torque convertor felt ok when sitting in bell housing and felt located fine,it also bolted up to flexiplate no probs also so dont no what the prob is any ideas
 
"Ashcroft transmissions"

Good link :mil10:

I was looking for a thumbs up smiley but liked this one instead
 
As mentioned fuse 11 is a common one but the dash normally beeps away and says “Transfer neutral”. I think the instrument cluster dong is the only thing that does break on one of these things.
 
al-one-arm said:
i dont suppose someone has put the fuse 11 in to tow it?
Click to expand...
dont know as i towed it myself but it was recovered to the previous owner by aa so its a poss were does fuse 11 live then please and would this cause the problems im excperiencing? not able to get to car till next weekend so cant check this till then, thanks heres hoping its that simple
icon4.gif
 
Fuse 11 should be homeless except in the unfortunate event you need to tow the vehicle on all four wheels. In these cases it resides in the side of the drivers seat. With the fuse in, transfer neutral is selected, remove after towing.
 
You must log in or register to reply here.

Similar threads

P
L322 TD6 lost all drive
Replies
5
Views
297
backinblack
backinblack
tarphenry
p38 diesel
Replies
15
Views
1K
tarphenry
tarphenry
Flossie
P38A Am i stranded? EML on..
2 3
Replies
41
Views
2K
Rubberknees
Rubberknees
ar1g3
P38A P38 rattle at idle
2
Replies
26
Views
4K
roythebus
R
C
L322 td6 auto 2005 No Drive when hot
Replies
12
Views
1K
chu017
C
Back
Top