P38 2.5 Diesel 2000 in Berkshire will not start

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
T

The Engineer

New Member
Posts
2
Location
Reading
I have a problem with my 2.5 Diesel it has fuel up to pump but no fuel at the injectors. 12 volt at the stop switch. No faults on the dash and no faults when connected and checked with a hawkeye.
The car has done 94,000 miles and was running fine prior to not starting.
Any help or advice would be much appreciated

Thanks
 
The Engineer said:
I have a problem with my 2.5 Diesel it has fuel up to pump but no fuel at the injectors. 12 volt at the stop switch. No faults on the dash and no faults when connected and checked with a hawkeye.
The car has done 94,000 miles and was running fine prior to not starting.
Any help or advice would be much appreciated

Thanks
Click to expand...
Faulty stop solenoid ? Take it off and bench test it. Easier if you remove the inlet manifold
 
With the ignition OFF, take a length of wire from the battery +, and tap it onto the stop solenoid. It should click on tapping it, if not it's buggered! If it clicks for the first few taps and then stops.......... It's buggered!!;)
 
The Engineer said:
I have a problem with my 2.5 Diesel it has fuel up to pump but no fuel at the injectors. 12 volt at the stop switch. No faults on the dash and no faults when connected and checked with a hawkeye.
The car has done 94,000 miles and was running fine prior to not starting.
Any help or advice would be much appreciated

Thanks
Click to expand...
Loss of sync?
 
Sounds like the same problem I had. Was the fuel stop solenoid. Huge long thread about mine but basically that's what it was. Happy to come and help if required.
 
You can undo the stop solenoid and take out the plunger and refit the solenoid without the plunger to confirm it is the solenoid. This will also enable you to use the vehicle whilst waiting for a new solenoid. The engine won't turn off on the key like this so you will need to stall it.
 
Interceptorxj said:
You can undo the stop solenoid and take out the plunger and refit the solenoid without the plunger to confirm it is the solenoid. This will also enable you to use the vehicle whilst waiting for a new solenoid. The engine won't turn off on the key like this so you will need to stall it.
Click to expand...

Nonsense. The stop solenoid is a backup to the system that shuts the engine down in the event of a failure of the quantity servo to avoid a runaway. It is not safe to run the engine without a working stop solenoid. The engine will shut down when power is removed from the quantity servo and it returns to a no fuel position.
 
Interceptorxj said:
You can undo the stop solenoid and take out the plunger and refit the solenoid without the plunger to confirm it is the solenoid. This will also enable you to use the vehicle whilst waiting for a new solenoid. The engine won't turn off on the key like this so you will need to stall it.
Click to expand...
Oh no not this load of **** advice again. Don't do it .:eek: see what you have started @kapilamuni .:rolleyes:​
 
You must log in or register to reply here.

Similar threads

P
P38 2.5 None start
Replies
5
Views
567
Mark Piercy
Mark Piercy
C
P38 diesel not starting
3 4 5
Replies
97
Views
5K
Grrrrrr
Grrrrrr
tarphenry
p38 diesel
Replies
15
Views
571
tarphenry
tarphenry
Paul Coddington
EAS being a pain, again
2
Replies
26
Views
2K
Paul Coddington
Paul Coddington
A
P38 2.5 Diesel - running issues
2
Replies
24
Views
2K
Datatek
Datatek
Back
Top