Not a bobtail a 6x6
- Thread starter pierreblonde
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
I’ve got a canny start with the chassis now
Did some setting out and makes some reference lines. I cut it on the straight by the box as I’m going to extend it there , I’m thinking by 20” at the minute
I the cut the back off in front of the rear spring seat and I’m using the section where it rises up as my overlap . Made a template and cut the sides out then welded 40mm box spacers between before the top and bottom strips went on, they fit over the the original chassis legs
used the original round crossmember and made new ones for the rest with new spring seats. I set the round crossmember and first spring seat up from the workshop manual. Then made a jig and repeated it for the second one.
I’ve done the brackets for the tank and mounted that just have the trailing arm mounts to do and some brackets. I’ll finish the back before I join it back together
And sorry I’ve no idea why the pictures always end up sideways
Did some setting out and makes some reference lines. I cut it on the straight by the box as I’m going to extend it there , I’m thinking by 20” at the minute
I the cut the back off in front of the rear spring seat and I’m using the section where it rises up as my overlap . Made a template and cut the sides out then welded 40mm box spacers between before the top and bottom strips went on, they fit over the the original chassis legs
used the original round crossmember and made new ones for the rest with new spring seats. I set the round crossmember and first spring seat up from the workshop manual. Then made a jig and repeated it for the second one.
I’ve done the brackets for the tank and mounted that just have the trailing arm mounts to do and some brackets. I’ll finish the back before I join it back together
And sorry I’ve no idea why the pictures always end up sideways
- Posts
- 21,044
- Location
- In the next Glen
Im loving this the shell looks superb well done. 
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Thanks very muchIm loving this the shell looks superb well done.
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Picked a axle up last week. I’ve got the others stripped to rebuild in boxes. So before I pulled this down I used it to setup the trailing arm mounts. Made some templates out of ply first. Went on ok in the end after a bit fitting.
It was looking a bit tight to the spring seat. So I ended up moving them and the back seats back 25mm. I’m setting the axles up for 275.75r tyres. So now I have 150mm between tyres. But it should look ok
next job will be the extension in the middle then join the front back on
It was looking a bit tight to the spring seat. So I ended up moving them and the back seats back 25mm. I’m setting the axles up for 275.75r tyres. So now I have 150mm between tyres. But it should look ok
next job will be the extension in the middle then join the front back on
kurtjohnson10
Well-Known Member
- Posts
- 15,221
- Location
- midlands
Me as well mate, refreshing to see something like this done. Would not have the cash and patience to do it myself though.Im loving this the shell looks superb well done.
- Posts
- 21,044
- Location
- In the next Glen
Me as well mate, refreshing to see something like this done. Would not have the cash and patience to do it myself though.
I have the space & patience trouble is I keep buying other things half way through then end up with loads of projects
half done then no time to do any as the misses keeps finding me sh!t to do at the house ffs ive just done the kitchen
last week bedroom last month & the whole outside new metal railings,slabs ect ect few weeks ago I done 15m of
gabion baskets & hand balled 10 tonne of gravel for the drive. fkn disco is lying stripped but my 90 is just motd n taxed
Im hoping she gives me piece for a few weeks so I can crack on with mine now the house is done (I think lol)
- Posts
- 21,044
- Location
- In the next Glen
I have the space & patience trouble is I keep buying other things half way through then end up with loads of projects
half done then no time to do any as the misses keeps finding me sh!t to do at the house ffs ive just done the kitchen
last week bedroom last month & the whole outside new metal railings,slabs ect ect few weeks ago I done 15m of
gabion baskets & hand balled 10 tonne of gravel for the drive. fkn disco is lying stripped but my 90 is just motd n taxed
Im hoping she gives me piece for a few weeks so I can crack on with mine now the house is done (I think lol)
Edit.... just been reminded ive got new driveway gates to make ffs
never ending pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Bit of an update , got the front part of the chassis joined back together I added 15” in the middle. I made a couple of lengths of box up out of 3 mm to go inside the chassis legs then put some 2mm between and folded them insitu to bring it out flush and match it to the original chassis
I left the gearbox crossmember in until I got it all welded. I made up a couple of outriggers and got them on to match the body mounts I’ve made on the shell. The got it turned over and finished the welding underneath
still got some bits of brackets and suck to do for were I think the exhaust hangers will be and clean welds up. I cleaned the front of the chassis down and used aquasteel on it which seems great stuff. The it will all get a rust proof primer that Würth does. The just a satin black chassis paint. And heads up for a good one will be appreciated. On hols atm so not get anything done. But my heads running riot !
ps sorry I still can’t get the pics the right way up
I left the gearbox crossmember in until I got it all welded. I made up a couple of outriggers and got them on to match the body mounts I’ve made on the shell. The got it turned over and finished the welding underneath
still got some bits of brackets and suck to do for were I think the exhaust hangers will be and clean welds up. I cleaned the front of the chassis down and used aquasteel on it which seems great stuff. The it will all get a rust proof primer that Würth does. The just a satin black chassis paint. And heads up for a good one will be appreciated. On hols atm so not get anything done. But my heads running riot !
ps sorry I still can’t get the pics the right way up
- Posts
- 12,098
- Location
- Sud ouest France !
Why are you not doing this for a living??
Brilliant stuff kidda.
Brilliant stuff kidda.
towsey956
Well-Known Member
- Posts
- 1,104
- Location
- Northyorkshire
Just seen this...you are a man that should be proud of himself!
Towsey
Towsey
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
CheersWhy are you not doing this for a living??
Brilliant stuff kidda.
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Cheers
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
I’m thinking about doing away either the A frame for the first rear axle and put A Panhard rod on it instead , so I have room over it for the prop to the second rear axle. I had a look on line and there’s kits for D2’s for that. would there be any issues doing that but leaving the A frame on the back one .
as l’ll set it up when the chassis is on it’s back to fabricate mounts etc?
Hicap phill
Well-Known Member
- Posts
- 15,378
- Location
- Wiltshire
Why not do panard rod set up a On both axles?
Only that 2 different set ups could conflict.
I thought D2 use a different set up?
Only that 2 different set ups could conflict.
I thought D2 use a different set up?
Hicap phill
Well-Known Member
- Posts
- 15,378
- Location
- Wiltshire
@pierreblonde Here’s another 6x6 build.
Axles are already on so you might get some ideas
https://www.landyzone.co.uk/land-rover/defender-6x6-camper-build-thread.356889/page-3#post-4943894
Axles are already on so you might get some ideas
https://www.landyzone.co.uk/land-rover/defender-6x6-camper-build-thread.356889/page-3#post-4943894
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Yeah. I did think about that too just wasn’t sure what it would be like. Yes the D2 has a watts linkage on them not the A frame
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
It’s going to look great that. I’m wanting to keep the diffs on the same side. I’ll rotate the axle nose up slightly on the back axle and chance to overfill it slightly to keep the pinion bearing wet. I don’t want the prop coming off the axle in front it. So I don’t have sort of two lots of movement on that prop to worry about. I’m looking a picking the drive up with something just behind the transfer box then running the prop independently to the last axle through a centre carrier. That’s why I want to get rid of the A frame. However there’s nothing set in stone
Hicap phill
Well-Known Member
- Posts
- 15,378
- Location
- Wiltshire
another Special build is foley 4x4 they may have ideas for the rear axles.
