P38A BM CATS anyone?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
MrGorsky

MrGorsky

Well-Known Member
Full Member
Posts
1,527
Location
Buckinghamshire.
My exhaust is blowing in the area of the Cats and I'll need to replace them I think.

Having a look around 't web I've found these and these on eBay that are much cheaper than the usual suspects. I'm not keen on fitting the cheapest usually, but work is a bit scarce at the moment, and so cheap it has to be....... so long as they actually fit and work.

Does anyone have any experience of BM Catalysts? Googling them suggests reasonable quality, albeit with rough looking welds sometimes. I don't go under the cat much to look at the welding on the exhaust TBH so I'm fine with that.

Anyone got any recommendations for replacement catalysts?

P38 V8 4.6 GEMS.
 
MrGorsky said:
My exhaust is blowing in the area of the Cats and I'll need to replace them I think.

Having a look around 't web I've found these and these on eBay that are much cheaper than the usual suspects. I'm not keen on fitting the cheapest usually, but work is a bit scarce at the moment, and so cheap it has to be....... so long as they actually fit and work.

Does anyone have any experience of BM Catalysts? Googling them suggests reasonable quality, albeit with rough looking welds sometimes. I don't go under the cat much to look at the welding on the exhaust TBH so I'm fine with that.

Anyone got any recommendations for replacement catalysts?

P38 V8 4.6 GEMS.
Click to expand...
They seem well enough made, fitted one to a mates car with no issues.
 
Second hand info, but a friend fitted two of these. Quality is ok, passed emmisions, just a bit of fettling as the pipes were slightly different size but not much.
 
Gunnerhavesome said:
Hmm CE Chinese export only joking but you never know.
Click to expand...
Not much difference, I used to manufacture micro controllers, all I had to do to legally CE mark them was to create a file describing the function and steps taken to ensure safety and RF interference compliance. No checks are made unless and until something goes wrong causing injury for example. It's a joke, now the UK is leaving the EU I hope they bring back the BSI kite mark and the British standards institution.
 
So I've fitted my BM CATS. They seem very well made, fitted no problem without me having to do any fettling, so I call that a success!

One small drawback was that the gaskets that came with the fitting kit they include came with only 8mm holes for the exhaust manifold flange studs, and they're 10mm on a P38. Luckily I has a spare pair in the garage.

Very happy with them, and for the price (£116 delivered) I don't think you can beat them!
 
Last edited:
It's not as shiny as it was now because I've been for a run! He we are though...

IMG_9282.JPG
IMG_9277.JPG
IMG_9279.JPG
IMG_9281.JPG
IMG_9283.JPG
IMG_9284.JPG
 
Last edited:
You must log in or register to reply here.

Similar threads

MrGorsky
P38A Occasional "Engine Disabled Press Remote" message on dash.
Replies
19
Views
1K
Datatek
Datatek
T
P38A P38 DSE Manual (non-EGR) No turbo boost
Replies
7
Views
785
Grrrrrr
Grrrrrr
H
D2 ABS Sensors
Replies
3
Views
387
sierrafery
sierrafery
Blob
L322 Parking Aid Module - what's the difference?
Replies
4
Views
588
pwood999
pwood999
Gorf
5.0 SC rebuild
Replies
6
Views
1K
marjon
marjon
Back
Top