P38A BeCM lockout and other gremlins

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
H

Highland_exile

New Member
Posts
6
Location
North of Scotland
Hi all you clever lot.
Looking for some assistance
I have recently got a 2000 P38a 2.5dhse. High mileage but mechanically good, electrically not so.
A previous owner has fitted an isolator, I assume to combat battery drain/alarm issues. I have one key, and the remote fob is goosed. I have spurious locking unlocking when driving, and occasionally when parked up with isolator on. I've had the immobiliser cut in a couple times, but got going with the EKA. But this time it seems to have locked itself out. Not recognising the EKA, I have checked the door latch switches and the switches are all operating as they should. Could anyone recommend someone who can unlock a BeCM and function test it?
I have numerous niggles which appear to come from the BeCM, rear wiper not working, electric seats not working and couple other which escape me just now.
No big rush, it's primarily a farm truck/2nd car and I'm away at sea for a couple weeks tomorrow.

Any help, recommendations or pointers appreciated
 
@Rick-the-Pick on here is the BECM guru. I think what you have is either spurious RF interference or an issue with the lock ground, either due to a dodgy microswitch (try a load instead of DVM) or possibly the tailgate switch need a dose of looking at. Possibly a mix of both. @martyuk also is good with BECMs but don't think he's back from NZ yet.
 
Ahh yes tailgate switch, that's another one that could be temperamental. How's that affect the central locking or immobiliser? Never had a tailgate open warning on the dash, unless it actually was open.
 
Here is martyuk`s door lock test sheet, if it loads ok

the tailgate latch earths though the drivers door lock
 

Attachments

  • P38 Door Latch Tests (2).pdf
    90.3 KB · Views: 198
Buy a replacement case, buttons & batteries and insert your PCB. If you're not confident in doing that, send the Fob for repair / refurb. Then re-instate the RF receiver and get things working properly. If can has the older receiver versions and you suffer from RF interference, then unplug the antenna. The fob will still work, but only next to left rear window !!

Regular battery disconnect can often cause BECM & ECU out of sync, but they should re-sync automatically if using the fob. Do you always leave door open & key out before switching the isolator ?

Best thing is to resolve the battery drain, and then you could leave it for weeks with no issues.
 
Thanks for all the advice, will be giving it a good dose of looking at when I get home in a couple weeks.
Have followed Marty's test sheet, and while its damp and worn, the door latch seems ok. Will check out the tailgate switch when home again. Worth a look, as every time it has locked out, the boot has been playing up for a few days, now its totally locked out the only doors I can open are the boot and drivers.
Would like to get rid of the isolator, and get it working properly again. The Mrs is amiable to spending a bit of money on it, cos it makes for a nice comfy farm truck when it works, and we can rid of her little thing.
Is Marty the same Marty that does http://p38webshop.co.uk/ ? If so, I've already emailed him about unlocking the BeCM.
 
Give Les at Classic Rides North Wales a call. Very helpful, always got time for a chat and can help you out with BeCM repairs, keys, fobs etc. I speak from experience.
 
Just got back so bear with me I'm knackered, have you checked the block connectors at the bottom of the A posts behind the plastic kick panels these corrode and cause all sorts of problems, cutting them out soldering and heat shrink the wires is the best option..I thought it was an old thread when I saw @Datatek had posted, welcome back Keith.;)
 
tomcat59alan said:
Just got back so bear with me I'm knackered, have you checked the block connectors at the bottom of the A posts behind the plastic kick panels these corrode and cause all sorts of problems, cutting them out soldering and heat shrink the wires is the best option..I thought it was an old thread when I saw @Datatek had posted, welcome back Keith.;)
Click to expand...
Thanks Alan, hope you are keeping well. House renovations finally finished, so I have a bit more time. Just all the logs to cut for winter.
 
Thanks for all the help, heard from Marty, he's out the country at the moment, have been in contact with callrova, and crnw. Waiting for an opportunity to get the BeCM and Ecu out the truck, had a couple job interviews as soon as I got home, and now I'm free to attack it, it's been chucking it down and the truck is outside:mad: hopefully get at it at the weekend.
 
You must log in or register to reply here.

Similar threads

I
P38 BeCM locked?
Replies
8
Views
867
pwood999
pwood999
DollyBird
Engine disabled, keys not working, tried the guide “Re-synching the Range Rover P38 diesel engine with the Solved - BECM using a Nanocom” no luck
Replies
9
Views
1K
DollyBird
DollyBird
Jazydave
Blower fans
Replies
12
Views
447
Datatek
Datatek
A
P38A Cruise control question ( wheel speed issue )
Replies
16
Views
1K
AndyF07
A
T
Becm problem
Replies
17
Views
2K
taeman
T
Back
Top