Search results

Well, that's it, I've screwed up a rear wheel bolt, can some kind soul tell me if it can be done and how it can be changed (please in detail)? where to buy replacement? THANKS

Hi again guys. I changed the cardan bearings because they were old, as soon as I put the new ones they make noise and vibrate a little at low speed. I have taken care to mount them well and at a 90º angle, I marked the washers and transfer to mount it in the same position. Could they be faulty...

Hi guys. For Freelander 1 2005 TD4. Can any of you tell me if Mobil ATF 3309 is valid for the automatic gearbox? Can it be mixed with the original? Alternatives? Thank you so much.

Hi guys: I have in my sights a freel2 2009 TD4.e start-stop 236000km. I have read that the flywheel has been reinforced with carbon steel and the clutch disc is seven times stronger than the version without s / stp. Does this reduce clutch disc wear? Haldex is gen III or IV? Has the rear...

HI: I have had other automatic gearbox but never in LR, my doubt: with the lever in D or R I have to firmly press the brake or the car starts the march. Is it normal that there is no "dead" space and push so much? Will it damage torque converter or something? I know there are jatco specialists...

Hi: I bought a 10mm diameter and 1.20cm long wire to install a second ground wire. Does it make sense to install a second negative cable in FL1 Td4? Which has benefits? Where does it connect? Thank you.

Hi Friends. when starting a movement or driving very slowly (1st gear) forward and with the steering wheel fully turned to the left makes a noise woouUH! woouUH! When accelerating it disappears. Ideas? CV joint, transmission, VCU bearings, transfer (I hope not)? Thanks and stay safe.

Please help. After a large disassembly to repair things, I find a connector that I do not know where it plugs in, if it does. I think it was loose and it looks like it is not connected. I s the connector that comes out of the cables of the air conditioning compressor. Does anyone know where it...

Hi: to solve the problem of oil in the intake I am adapting a decanter to the breather tube of the block. The point is that I have to reduce the diameter of the tube to 1/3. Will there be a problem with breathing?, will it bring other adverse effects or not? I made the same system in a...

Hi guys. I have received led fog lights. Additionally, by surprise, the box contains two small bulbs, does anyone know where they are for? Thanks

Hi. Doing vacuum test dissamblin the hoses of the vacuum tank and using a manual vacuum pump Connecting the pump directly to the pipe of turbo solenoid the vac does not hold, instead, it stays in the egr solenoid pipe. All pipes are new. Is it normal or both should hold the vac? Thanks for...

Hi friends. I can't move the alternator auxiliary belt tensioner. It must be moved counterclockwise to loosen but no matter how hard I do it is impossible. Is it stuck? Any idea how to loosen it even if I have to change the tensioner? Any fantastic idea to dissamble the tensioner without...

Hi. need help to choose device. I published this thread in other forum, maybe was no the correct place. I know in this forum there are a very good specialists in this themes: Thinking to buy a scan tool but I'm not sure what choose between 4 models. I seek large functions including automatic...

Hi friends. Black Friday is very near. Thinking to buy a scan tool but I'm not sure what choose between 4 models. I seek large functions including automatic gearbox oil temperature, coding injectors, live data, actuator test in adiction to the basic DCT ABS, BRAKE, reset and regeneration...

Hi friends: I have done a search but I need very concrete instruction because in car audio (an many other things) I am all ignorant. I don't know where to start: I have HK sound equipment. I fixed the distorted subwoofer, testing channel by channel with balance and fader I checked that the...

Hi. Few dais ago I felt the car shaking when the engine stoped. Aided by an iron bar, I moved to the sides the rear part (thick) of the upper right engine tie rod. The iron support moved very easily on the rubber support. It seemed loose. The repair I did minimized greatly the shaking when...

Sorry for my lousy English. I have had about 6 freelanders 1 and 2. There are many good experts here. I have learned a lot. Now I try to give you back what little I know.